All FAQs (Helpie FAQ)

Sample of All FAQs (Helpie FAQ)

Helpie FAQ

  • Environmental features
    Power source  220–240 V, 50/60 Hz—Asia Pacific
    110 V, 60 Hz—Taiwan 
     Power consumption  1,850 W or less—maximum power, Asia Pacific
    1,584 W or less—maximum power, Taiwan
    763.3 W—operating power, black and white
    871.2 W—operating power, colour
    40.1 W—Ready Mode 
    0.32 W—Energy Saver Mode (Sleep Mode)
     Typical Electricity Consumption (TEC)  0.67 kWh
     Warm-up time  

    23 seconds

     Recovery time  From Energy Saver Mode
    7.4 seconds
     Green labels  The Thai Green Label Scheme
     Other environmental features  Eco-friendly indicator, Energy Saver Timer, System Reset Timer
  • Software and solutions
    Standard @Remote Embedded Web Image Monitor
    Optional Streamline NX V3 GlobalScan NX Enhanced Locked Print NX Card Authentication Package
    Mobile apps RICOH Smart Device Connector
  • Supported operating environments
    Windows PCL 5c, PCL 6, and PostScript 3 Windows 8.1 Windows 10 Windows Server 2012 Windows Server 2012 R2 Windows Server 2016 Windows Server 2019 Windows Server 2022
    Macintosh MacOS v10.15 or later—PostScript 3 only
    Unix PCL 5c, PostScript 3 Sun Solaris, HP-UX, SCO OpenServer, Red Hat Linux, IBM AIX
    SAP PCL 5c R/3, S/4
  • Security features
    Encryption SSD, PDF, Secure print, WEP, WPA Authentication password Encryption of data sent via Scan to email and Fax forwarding (S/MIME)
    Authentication 802.1x wired authentication Administrator authentication IEEE 802.11i security (WPA2) IPv6 Quota setting User authentication—Windows and LDAP via Kerberos, basic, user code WiFi Protected Setup (WPS) support
  • Fax features
    Fax types G3 fax, Internet fax (T.37), IP fax (T.38), LAN-Fax, Paperless fax, Direct SMTP fax
    Fax circuit PSTN, PBX
    Fax compatibilty ITU-T (CCITT), G3—maximum 3 lines
    Fax modem speed 2,400 bps–33.6 Kbps—G3, standard with automatic shift down
    Fax compression methods MH, MR, MMR, JBIG
    Fax resolution Standard mode 200 x 100 dpi—8 x 3.85 lines/mm Detail mode 200 x 200 dpi—8 x 7.7 lines/mm Super Fine mode 400 x 400 dpi—8 x 15.4 lines/mm 400 x 400 dpi—16 x 15.4 lines/mm Note: Super Fine mode is supported with the optional SAF memory.
    G3 fax transmission speed 3 seconds approximately—JBIG, ITU-T No. 1 chart, TTI off, memory transmission 3 seconds approximately—MMR, ITU-T No. 1 chart, TTI off, memory transmission
    Fax SAF memory capacity Standard 4 MB—approximately 320 pages With optional SAF memory 60 MB—approximately 4,800 pages
    Fax memory backup 1 hour
    Quick dials 2,000 numbers
  • Scan feautures
    Scan speed Via SPDF
    150 ppm—simplex, 200 x 200 dpi
    120 ppm—simplex, 300 x 300 dpi
    300 ppm—duplex, 200 x 200 dpi
    220 ppm—duplex, 300 x 300 dpi
    Scan methods

    Scan to USB, Scan to email, Scan to folder, Scan to URL, Scan to MSB, Scan to FTP, Scan to PDF/A, Scan to digitally signed PDF, Scan to searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Colour scanning Standard
    Scan resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi, 1,200 dpi
    Note:1,200 dpi scanning is supported only with A5 or smaller paper size.
    Scan to file types Single- and multi-page TIFF
    Single-page JPEG
    Single- and multi-page PDF, PDF/A
    Single- and multi-page high-compression PDF
    Scan to email

    Protocols
    SMTP gateway, TCP/IP, POP, IMAP 4

    Authentication

    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Scan to email file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Scan to folder

    Protocols
    SMB, FTP

    Resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Search for client folders
    SMB—browsing directly to the designated folder
    FTP—by folder name

    Scan to folder file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note:Optional OCR unit is required to support scanning to a searchable PDF.

    TWAIN scanning Scan mode
    Standard, Photo, OCR, Filing
    Note: Optional OCR unit required for OCR scanning.

    Scan resolution
    100–1,200 dpi
    Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
  • Print features
    Print speed colour 60 ppm
    Print speed black and white 60 ppm
    First print time 2.4 seconds black and white, 3.8 seconds colour
    Print resolution 1,200 x 1,200 dpi
    Page description languages (PDLs) Standard PCL 5c, PCL 6,PostScript 3 emulation, PDF Direct emulation Optional Genuine Adobe PostScript 3, PDF Direct from Adobe
    Printer drivers Standard PCL 5c, PCL 6,PostScript 3 emulation Optional Genuine Adobe PostScript 3
    Duplex printing Standard
    Mobile printing Yes
  • Copy features
    Copy speed 60 cpm
    First copy time 2.9 seconds—black and white
    4.2 seconds—colour
    Copy resolution 100, 200, 300, 400, 600 dpi—scanning
    1,200 x 1,200 dpi (maximum)—printing
    Zoom range 25%–400% in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 87%, 82%, 71%, 61%, 50%, 25%
    Duplex copy Simplex to duplex, duplex to duplex—with SPDF, book to duplex, front and back to duplex
    Book copy Booklet, magazine, layout and booklet
  • Connectivity
    Interfaces - standard

    Mainframe
    10Base-T/100Base-Tx (Ethernet)
    1000Base-T (Gigabit Ethernet)
    USB Host Type A—2 ports
    USB Type B—1 port

    Smart Operation Panel
    Bluetooth 5.21
    USB Host Type A—USB Flash memory
    USB Host Type A—optional 1 port for USB keyboard

    1
    —Cannot be used for printing

    Interfaces - optional IEEE 802.11 a/b/g/n/ac Interface Unit Type M52
    Device Server Option Type M52 (additional Ethernet/Gigabit Ethernet port)
    Network protocols - standard TCP/IP (IPv4, IPv6)
  • Media Handling
    Standard input capacity (sheets) 1,200
    Maximum input capacity (sheets) 4,700
    Standard output capacity (sheets) 500
    250—B4 or larger
    Maximum output capacity (sheets) 3,625
    Paper input configuration - standard 2 x 550-sheet paper trays, 100-sheet bypass tray, 220-sheet SPDF, duplex unit
    Paper output configuration - standard 500-sheet face-down internal output tray
    Supported media

    Tray 1
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper

    Tray 2
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper, envelope

    Optional trays
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper

    Bypass tray
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper, label paper

    Maximum paper size SRA3
    Media weight (g/m2) 52–300
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 701 x 963 mm
    Weight—mainframe 100.8 kg
  • Configuration
    Functions Copy, print, scan, optional fax
    Colour Yes
    HDD 256 GB SSD
    Memory - standard 8 GB—4 GB mainframe + 4 GB Smart Operation Panel
    Operation panel 10.1" Smart Operation Panel
  • Environmental features
    Power source 220–240 V, 50/60 Hz—Asia Pacific
    110 V, 60 Hz—Taiwan
    Power consumption 1,850 W or less—maximum power, Asia Pacific
    1,584 W or less—maximum power, Taiwan
    576.6 W—operating power, black and white
    664.9 W—operating power, colour
    40.5 W—Ready Mode
    0.32 W—Energy Saver Mode (Sleep Mode)
    Typical Electricity Consumption (TEC) 0.45 kWh
    Warm-up time

    23 seconds

    Recovery time From Energy Saver Mode
    6.3 seconds
    Green labels The Thai Green Label Scheme
    Other environmental features Eco-friendly indicator, Energy Saver Timer, System Reset Timer
  • Software and solutions
    Standard @Remote Embedded
    Web Image Monitor
    Optional Streamline NX V3
    GlobalScan NX
    Enhanced Locked Print NX
    Card Authentication Package
    Mobile apps RICOH Smart Device Connector
  • Supported operating environments
     Windows PCL 5c, PCL 6, and PostScript 3 Windows 8.1 Windows 10 Windows Server 2012 Windows Server 2012 R2 Windows Server 2016 Windows Server 2019 Windows Server 2022
     Macintosh  MacOS v10.15 or later—PostScript 3 only
     Unix  PCL 5c, PostScript 3 Sun Solaris, HP-UX, SCO OpenServer, Red Hat Linux, IBM AIX
     SAP  PCL 5c R/3, S/4
  • Security features
     Encryption SSD, PDF, Secure print, WEP, WPA Authentication password Encryption of data sent via Scan to email and Fax forwarding (S/MIME)
     Authentication  802.1x wired authentication Administrator authentication IEEE 802.11i security (WPA2) IPv6 Quota setting User authentication—Windows and LDAP via Kerberos, basic, user code WiFi Protected Setup (WPS) support
  • Scan features
    Scan speed Via SPDF
    150 ppm—simplex, 200 x 200 dpi
    120 ppm—simplex, 300 x 300 dpi
    300 ppm—duplex, 200 x 200 dpi
    220 ppm—duplex, 300 x 300 dpi
    Scan methods

    Scan to USB, Scan to email, Scan to folder, Scan to URL, Scan to MSB, Scan to FTP, Scan to PDF/A, Scan to digitally signed PDF, Scan to searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Colour scanning Standard
    Scan resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi, 1,200 dpi
    Note:1,200 dpi scanning is supported only with A5 or smaller paper size.
    Scan to file types Single- and multi-page TIFF
    Single-page JPEG
    Single- and multi-page PDF, PDF/A
    Single- and multi-page high-compression PDF
    Scan to email

    Protocols
    SMTP gateway, TCP/IP, POP, IMAP 4

    Authentication

    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Scan to email file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Scan to folder

    Protocols
    SMB, FTP

    Resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Search for client folders
    SMB—browsing directly to the designated folder
    FTP—by folder name

    Scan to folder file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note:Optional OCR unit is required to support scanning to a searchable PDF.

    TWAIN scanning Scan mode
    Standard, Photo, OCR, Filing
    Note: Optional OCR unit required for OCR scanning.

    Scan resolution
    100–1,200 dpi
    Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
  • Fax feautures
    Fax types G3 fax, Internet fax (T.37), IP fax (T.38), LAN-Fax, Paperless fax, Direct SMTP fax
    Fax circuit PSTN, PBX
    Fax compatibilty ITU-T (CCITT), G3—maximum 3 lines
    Fax modem speed 2,400 bps–33.6 Kbps—G3, standard with automatic shift down
    Fax compression methods MH, MR, MMR, JBIG
    Fax resolution Standard mode 200 x 100 dpi—8 x 3.85 lines/mm Detail mode 200 x 200 dpi—8 x 7.7 lines/mm Super Fine mode 400 x 400 dpi—8 x 15.4 lines/mm 400 x 400 dpi—16 x 15.4 lines/mm Note: Super Fine mode is supported with the optional SAF memory.
    G3 fax transmission speed 3 seconds approximately—JBIG, ITU-T No. 1 chart, TTI off, memory transmission 3 seconds approximately—MMR, ITU-T No. 1 chart, TTI off, memory transmission
    Fax SAF memory capacity Standard 4 MB—approximately 320 pages With optional SAF memory 60 MB—approximately 4,800 pages
    Fax memory backup 1 hour
    Quick dials 2,000 numbers
  • Print features
    Print speed colour 45 ppm
    Print speed black and white 45 ppm
    First print time 3.2 seconds black and white, 5.2 seconds colour
    Print resolution

    1,200 x 1,200 dpi

    Page description languages (PDLs)

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation, PDF Direct emulation

    Optional
    Genuine Adobe PostScript 3, PDF Direct from Adobe

    Printer drivers

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation

    Optional
    Genuine Adobe PostScript 3

    Duplex printing Standard
    Mobile printing Yes
  • Copy features
    Copy speed 45 cpm
    First copy time 3.6 seconds—black and white 5.4 seconds—colour
    Copy resolution 100, 200, 300, 400, 600 dpi—scanning 1,200 x 1,200 dpi (maximum)—printing
    Zoom range 25%–400% in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 87%, 82%, 71%, 61%, 50%, 25%
    Duplex copy Simplex to duplex, duplex to duplex—with SPDF, book to duplex, front and back to duplex
    Book copy Booklet, magazine, layout and booklet
  • Connectivity
    Interfaces - standard

    Mainframe
    10Base-T/100Base-Tx (Ethernet)
    1000Base-T (Gigabit Ethernet)
    USB Host Type A—2 ports
    USB Type B—1 port

    Smart Operation Panel
    Bluetooth 5.21
    USB Host Type A—USB Flash memory
    USB Host Type A—optional 1 port for USB keyboard

    1
    —Cannot be used for printing

    Interfaces - optional IEEE 802.11 a/b/g/n/ac Interface Unit Type M52
    Device Server Option Type M52 (additional Ethernet/Gigabit Ethernet port)
    Network protocols - standard TCP/IP (IPv4, IPv6)
  • Media Handling
    Standard input capacity (sheets) 1,200
    Maximum input capacity (sheets) 4,700
    Standard output capacity (sheets) 500 250—B4 or larger
    Maximum output capacity (sheets) 3,625
    Paper input configuration - standard 2 x 550-sheet paper trays, 100-sheet bypass tray, 220-sheet SPDF, duplex unit
    Paper output configuration - standard 500-sheet face-down internal output tray
    Supported media Tray 1 Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper Tray 2 Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper, envelope Optional trays Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper Bypass tray Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper, label paper
    Maximum paper size SRA3
    Media weight (g/m2) 52–300
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 701 x 963 mm
    Weight—mainframe 100.8 kg
  • Configuration
    Functions Copy, print, scan, optional fax
    Colour Yes
    HDD 256 GB SSD
    Memory - standard 8 GB—4 GB mainframe + 4 GB Smart Operation Panel
    Operation panel 10.1" Smart Operation Panel
  • Environmental features
    Power source 220–240 V, 50/60 Hz—Asia Pacific
    110 V, 60 Hz—Taiwan
    Power consumption 1,700 W or less—maximum power, Asia Pacific
    1,584 W or less—maximum power, Taiwan
    500.5 W—operating power, black and white
    543.6 W—operating power, colour
    38.5 W—Ready Mode
    0.3 W—Energy Saver Mode (Sleep Mode)
    Typical Electricity Consumption (TEC) 0.35 kWh
    Warm-up time

    24 seconds

    Recovery time From Energy Saver Mode
    6.2 seconds
    Green labels The Thai Green Label Scheme
    Other environmental features Eco-friendly indicator, Energy Saver Timer, System Reset Timer
  • Software and solutions
    Standard @Remote Embedded
    Web Image Monitor
    Optional Streamline NX V3
    GlobalScan NX
    Enhanced Locked Print NX
    Card Authentication Package
    Mobile apps RICOH Smart Device Connector
  • Supported operating environments
    Windows PCL 5c, PCL 6, and PostScript 3
    Windows 8.1
    Windows 10
    Windows Server 2012
    Windows Server 2012 R2
    Windows Server 2016
    Windows Server 2019
    Windows Server 2022
    Macintosh MacOS v10.15 or later—PostScript 3 only
    Unix PCL 5c, PostScript 3
    Sun Solaris, HP-UX, SCO OpenServer, Red Hat Linux, IBM AIX
    SAP PCL 5c
    R/3, S/4
  • Security features
    Data Overwrite Security System (DOSS) - Standard Yes—optional HDD required
    Encryption SSD, PDF, Secure print, WEP, WPA
    Authentication password
    Encryption of data sent via Scan to email and Fax forwarding (S/MIME)
    Authentication 802.1x wired authentication
    Administrator authentication
    IEEE 802.11i security (WPA2)
    IPv6
    Quota setting
    User authentication—Windows and LDAP via Kerberos, basic, user code
    WiFi Protected Setup (WPS) support
  • Fax features
    Fax types G3 fax, Internet fax (T.37), IP fax (T.38), LAN-Fax, Paperless fax, Direct SMTP fax
    Fax circuit PSTN, PBX
    Fax compatibilty ITU-T (CCITT), G3—maximum 3 lines
    Fax modem speed 2,400 bps–33.6 Kbps—G3, standard with automatic shift down
    Fax compression methods MH, MR, MMR, JBIG
    Fax resolution

    Standard mode
    200 x 100 dpi—8 x 3.85 lines/mm

    Detail mode

    200 x 200 dpi—8 x 7.7 lines/mm

    Super Fine mode
    400 x 400 dpi—8 x 15.4 lines/mm
    400 x 400 dpi—16 x 15.4 lines/mm

    Note: Super Fine mode is supported with the optional SAF memory.

    G3 fax transmission speed 3 seconds approximately—JBIG, ITU-T No. 1 chart, TTI off, memory transmission
    3 seconds approximately—MMR, ITU-T No. 1 chart, TTI off, memory transmission
    Fax SAF memory capacity Standard
    4 MB—approximately 320 pages

    With optional SAF memory

    60 MB—approximately 4,800 pages
    Fax memory backup 1 hour
    Quick dials 2,000 numbers
  • Scan feautures
    Scan speed Via SPDF
    150 ppm—simplex, 200 x 200 dpi
    120 ppm—simplex, 300 x 300 dpi
    300 ppm—duplex, 200 x 200 dpi
    220 ppm—duplex, 300 x 300 dpi
    Scan methods

    Scan to USB, Scan to email, Scan to folder, Scan to URL, Scan to MSB, Scan to FTP, Scan to PDF/A, Scan to digitally signed PDF, Scan to searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Colour scanning Standard
    Scan resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi, 1,200 dpi
    Note:1,200 dpi scanning is supported only with A5 or smaller paper size.
    Scan to file types Single- and multi-page TIFF
    Single-page JPEG
    Single- and multi-page PDF, PDF/A
    Single- and multi-page high-compression PDF
    Scan to email

    Protocols
    SMTP gateway, TCP/IP, POP, IMAP 4

    Authentication

    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Scan to email file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Scan to folder

    Protocols
    SMB, FTP

    Resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Search for client folders
    SMB—browsing directly to the designated folder
    FTP—by folder name

    Scan to folder file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note:Optional OCR unit is required to support scanning to a searchable PDF.

    TWAIN scanning Scan mode
    Standard, Photo, OCR, Filing
    Note: Optional OCR unit required for OCR scanning.

    Scan resolution
    100–1,200 dpi
    Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
  • Print features
    Print speed colour 35 ppm
    Print speed black and white 35 ppm
    First print time 4.0 seconds black and white, 6.6 seconds colour
    Print resolution

    1,200 x 1,200 dpi

    Page description languages (PDLs)

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation, PDF Direct emulation

    Optional
    Genuine Adobe PostScript 3, PDF Direct from Adobe

    Printer drivers

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation

    Optional
    Genuine Adobe PostScript 3

    Duplex printing Standard
    Mobile printing Yes
  • Copy features
    Copy speed 35 cpm
    First copy time 4.5 seconds—black and white 6.9 seconds—colour
    Copy resolution 100, 200, 300, 400, 600 dpi—scanning 1,200 x 1,200 dpi (maximum)—printing
    Zoom range 25%–400% in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 87%, 82%, 71%, 61%, 50%, 25%
    Duplex copy Simplex to duplex, duplex to duplex—with SPDF, book to duplex, front and back to duplex
    Book copy Booklet, magazine, layout and booklet
  • Connectivity
     Interfaces - standard Mainframe 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet) USB Host Type A—2 ports USB Type B—1 port Smart Operation Panel Bluetooth 5.21 USB Host Type A—USB Flash memory USB Host Type A—optional 1 port for USB keyboard 1—Cannot be used for printing
     Interfaces - optional IEEE 802.11 a/b/g/n/ac Interface Unit Type M52 Device Server Option Type M52 (additional Ethernet/Gigabit Ethernet port)
     Network protocols - standard  TCP/IP (IPv4, IPv6)
  • Media Handling
    Standard input capacity (sheets) 1,200
    Maximum input capacity (sheets) 4,700
    Standard output capacity (sheets) 500
    250—B4 or larger
    Maximum output capacity (sheets) 1,625
    Paper input configuration - standard 2 x 550-sheet paper trays, 100-sheet bypass tray, 220-sheet SPDF, duplex unit
    Paper output configuration - standard 500-sheet face-down internal output tray
    Supported media

    Tray 1
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper

    Tray 2
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper, envelope

    Optional trays
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper

    Bypass tray
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper, label paper

    Maximum paper size SRA3
    Media weight (g/m2) 52–300
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 701 x 963 mm
    Weight—mainframe 99.3 kg
  • Configuration
    Functions Copy, print, scan, optional fax
    Colour Yes
    HDD 256 GB SSD
    Memory - standard 8 GB—4 GB mainframe + 4 GB Smart Operation Panel
    Operation panel 10.1" Smart Operation Panel
  • Environmental features
    Power source 220–240 V, 50/60 Hz—Asia Pacific
    110 V, 60 Hz—Taiwan
    Power consumption 1,700 W or less—maximum power, Asia Pacific
    1,584 W or less—maximum power, Taiwan
    464.4 W—operating power, black and white
    515.3 W—operating power, colour
    38.5 W—Ready Mode
    0.3 W—Energy Saver Mode (Sleep Mode)
    Typical Electricity Consumption (TEC) 0.30 kWh
    Warm-up time

    24 seconds

    Recovery time From Energy Saver Mode
    6.2 seconds
    Green labels The Thai Green Label Scheme
    Other environmental features Eco-friendly indicator, Energy Saver Timer, System Reset Timer
  • Software and solutions
     Standard  @Remote Embedded Web Image Monitor
     Optional  Streamline NX V3 GlobalScan NX Enhanced Locked Print NX Card Authentication Package
     Mobile apps  RICOH Smart Device Connector
  • Supported operating environments
    Windows PCL 5c, PCL 6, and PostScript 3
    Windows 8.1
    Windows 10
    Windows Server 2012
    Windows Server 2012 R2
    Windows Server 2016
    Windows Server 2019
    Windows Server 2022
    Macintosh MacOS v10.15 or later—PostScript 3 only
    Unix PCL 5c, PostScript 3
    Sun Solaris, HP-UX, SCO OpenServer, Red Hat Linux, IBM AIX
    SAP PCL 5c
    R/3, S/4
  • Security features
    Encryption SSD, PDF, Secure print, WEP, WPA
    Authentication password
    Encryption of data sent via Scan to email and Fax forwarding (S/MIME)
    Authentication 802.1x wired authentication
    Administrator authentication
    IEEE 802.11i security (WPA2)
    IPv6
    Quota setting
    User authentication—Windows and LDAP via Kerberos, basic, user code
    WiFi Protected Setup (WPS) support
  • Fax features
    Fax types G3 fax, Internet fax (T.37), IP fax (T.38), LAN-Fax, Paperless fax, Direct SMTP fax
    Fax circuit PSTN, PBX
    Fax compatibilty ITU-T (CCITT), G3—maximum 3 lines
    Fax modem speed 2,400 bps–33.6 Kbps—G3, standard with automatic shift down
    Fax compression methods MH, MR, MMR, JBIG
    Fax resolution

    Standard mode
    200 x 100 dpi—8 x 3.85 lines/mm

    Detail mode

    200 x 200 dpi—8 x 7.7 lines/mm

    Super Fine mode
    400 x 400 dpi—8 x 15.4 lines/mm
    400 x 400 dpi—16 x 15.4 lines/mm

    Note: Super Fine mode is supported with the optional SAF memory.

    G3 fax transmission speed 3 seconds approximately—JBIG, ITU-T No. 1 chart, TTI off, memory transmission
    3 seconds approximately—MMR, ITU-T No. 1 chart, TTI off, memory transmission
    Fax SAF memory capacity Standard
    4 MB—approximately 320 pages

    With optional SAF memory

    60 MB—approximately 4,800 pages
    Fax memory backup 1 hour
    Quick dials 2,000 numbers
  • Scan feautures
    Scan speed Via SPDF
    150 ppm—simplex, 200 x 200 dpi
    120 ppm—simplex, 300 x 300 dpi
    300 ppm—duplex, 200 x 200 dpi
    220 ppm—duplex, 300 x 300 dpi
    Scan methods

    Scan to USB, Scan to email, Scan to folder, Scan to URL, Scan to MSB, Scan to FTP, Scan to PDF/A, Scan to digitally signed PDF, Scan to searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Colour scanning Standard
    Scan resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi, 1,200 dpi
    Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
    Scan to file types Single- and multi-page TIFF
    Single-page JPEG
    Single- and multi-page PDF, PDF/A
    Single- and multi-page high-compression PDF
    Scan to email

    Protocols
    SMTP gateway, TCP/IP, POP, IMAP 4

    Authentication

    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Scan to email file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Scan to folder

    Protocols
    SMB, FTP

    Resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Search for client folders
    SMB—browsing directly to the designated folder
    FTP—by folder name

    Scan to folder file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note:Optional OCR unit is required to support scanning to a searchable PDF.

    TWAIN scanning Scan mode
    Standard, Photo, OCR, Filing
    Note: Optional OCR unit required for OCR scanning.

    Scan resolution
    100–1,200 dpi
    Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
  • Print features
    Print speed colour 30 ppm
    Print speed black and white 30 ppm
    First print time 4.0 seconds black and white, 6.6 seconds colour
    Print resolution

    1,200 x 1,200 dpi

    Page description languages (PDLs)

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation, PDF Direct emulation

    Optional
    Genuine Adobe PostScript 3, PDF Direct from Adobe

    Printer drivers

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation

    Optional
    Genuine Adobe PostScript 3

    Duplex printing Standard
    Mobile printing Yes
  • Copy features
    Copy speed 30 cpm
    First copy time 4.5 seconds—black and white 6.9 seconds—colour
    Copy resolution 100, 200, 300, 400, 600 dpi—scanning 1,200 x 1,200 dpi (maximum)—printing
    Zoom range 25%–400% in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 87%, 82%, 71%, 61%, 50%, 25%
    Duplex copy Simplex to duplex, duplex to duplex—with SPDF, book to duplex, front and back to duplex
    Book copy Booklet, magazine, layout and booklet
  • Connectivity
    Interfaces - standard Mainframe 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet) USB Host Type A—2 ports USB Type B—1 port Smart Operation Panel Bluetooth 5.21 USB Host Type A—USB Flash memory USB Host Type A—optional 1 port for USB keyboard 1—Cannot be used for printing
    Interfaces - optional IEEE 802.11 a/b/g/n/ac Interface Unit Type M52 Device Server Option Type M52 (additional Ethernet/Gigabit Ethernet port)
    Network protocols - standard TCP/IP (IPv4, IPv6)
  • Media Handling
    Standard input capacity (sheets) 1,200
    Maximum input capacity (sheets) 4,700
    Standard output capacity (sheets) 500 250—B4 or larger
    Maximum output capacity (sheets) 1,625
    Paper input configuration - standard 2 x 550-sheet paper trays, 100-sheet bypass tray, 220-sheet SPDF, duplex unit
    Paper output configuration - standard 500-sheet face-down internal output tray
    Supported media Tray 1 Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper Tray 2 Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper, envelope Optional trays Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper Bypass tray Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper, label paper
    Maximum paper size SRA3
    Media weight (g/m2) 52–300
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 701 x 963 mm
    Weight—mainframe 99.3 kg
  • Configuration
    Functions Copy, print, scan, optional fax
    Colour Yes
    HDD 256 GB SSD
    Memory - standard 8 GB—4 GB mainframe + 4 GB Smart Operation Panel
    Operation panel 10.1" Smart Operation Panel
  • Environmental features
    Power source 220–240 V, 50/60 Hz—Asia Pacific
    110 V, 60 Hz—Taiwan
    Power consumption 1,700 W or less—maximum power, Asia Pacific
    1,584 W or less—maximum power, Taiwan
    449.2 W—operating power, black and white
    494.5 W—operating power, colour
    37.7 W—Ready Mode
    0.3 W—Energy Saver Mode (Sleep Mode)
    Typical Electricity Consumption (TEC) 0.25 kWh
    Warm-up time

    24 seconds

    Recovery time From Energy Saver Mode
    6.6 seconds
    Green labels The Thai Green Label Scheme
    Other environmental features Eco-friendly indicator, Energy Saver Timer, System Reset Timer
  • Software and solutions
    Standard @Remote Embedded
    Web Image Monitor
    Optional Streamline NX V3
    GlobalScan NX
    Enhanced Locked Print NX
    Card Authentication Package
    Mobile apps RICOH Smart Device Connector
  • Supported operating environments
    Windows PCL 5c, PCL 6, and PostScript 3 Windows 8.1 Windows 10 Windows Server 2012 Windows Server 2012 R2 Windows Server 2016 Windows Server 2019 Windows Server 2022
    Macintosh MacOS v10.15 or later—PostScript 3 only
    Unix PCL 5c, PostScript 3 Sun Solaris, HP-UX, SCO OpenServer, Red Hat Linux, IBM AIX
    SAP PCL 5c R/3, S/4
  • Security features
    Encryption SSD, PDF, Secure print, WEP, WPA
    Authentication password
    Encryption of data sent via Scan to email and Fax forwarding (S/MIME)
    Authentication 802.1x wired authentication
    Administrator authentication
    IEEE 802.11i security (WPA2)
    IPv6
    Quota setting
    User authentication—Windows and LDAP via Kerberos, basic, user code
    WiFi Protected Setup (WPS) support
  • Fax features
    Fax types G3 fax, Internet fax (T.37), IP fax (T.38), LAN-Fax, Paperless fax, Direct SMTP fax
    Fax circuit PSTN, PBX
    Fax compatibilty ITU-T (CCITT), G3—maximum 3 lines
    Fax modem speed 2,400 bps–33.6 Kbps—G3, standard with automatic shift down
    Fax compression methods MH, MR, MMR, JBIG
    Fax resolution

    Standard mode
    200 x 100 dpi—8 x 3.85 lines/mm

    Detail mode

    200 x 200 dpi—8 x 7.7 lines/mm

    Super Fine mode
    400 x 400 dpi—8 x 15.4 lines/mm
    400 x 400 dpi—16 x 15.4 lines/mm

    Note: Super Fine mode is supported with the optional SAF memory.

    G3 fax transmission speed 3 seconds approximately—JBIG, ITU-T No. 1 chart, TTI off, memory transmission
    3 seconds approximately—MMR, ITU-T No. 1 chart, TTI off, memory transmission
    Fax SAF memory capacity Standard
    4 MB—approximately 320 pages

    With optional SAF memory

    60 MB—approximately 4,800 pages
    Fax memory backup 1 hour
    Quick dials 2,000 numbers
  • Scan feautures
    Scan speed Via ARDF
    80 ppm—200 x 200 dpi, 300 x 300 dpi
    Scan methods

    Scan to USB, Scan to email, Scan to folder, Scan to URL, Scan to MSB, Scan to FTP, Scan to PDF/A, Scan to digitally signed PDF, Scan to searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Colour scanning Standard
    Scan resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi, 1,200 dpi
    Note:1,200 dpi scanning is supported only with A5 or smaller paper size.
    Scan to file types Single- and multi-page TIFF
    Single-page JPEG
    Single- and multi-page PDF, PDF/A
    Single- and multi-page high-compression PDF
    Scan to email

    Protocols
    SMTP gateway, TCP/IP, POP, IMAP 4

    Authentication

    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Scan to email file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Scan to folder

    Protocols
    SMB, FTP

    Resolution
    100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Search for client folders
    SMB—browsing directly to the designated folder
    FTP—by folder name

    Scan to folder file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note:Optional OCR unit is required to support scanning to a searchable PDF.

    TWAIN scanning Scan mode
    Standard, Photo, OCR, Filing
    Note: Optional OCR unit required for OCR scanning.

    Scan resolution
    100–1,200 dpi
    Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
  • Print features
    Print speed colour 25 ppm
    Print speed black and white 25 ppm
    First print time 4.5 seconds black and white, 7.0 seconds colour
    Print resolution

    1,200 x 1,200 dpi

    Page description languages (PDLs)

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation, PDF Direct emulation

    Optional
    Genuine Adobe PostScript 3, PDF Direct from Adobe

    Printer drivers

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation

    Optional
    Genuine Adobe PostScript 3

    Duplex printing Standard
    Mobile printing Yes
  • Copy features
    Copy speed 25 cpm
    First copy time 5.1 seconds—black and white 7.4 seconds—colour
    Copy resolution 100, 200, 300, 400, 600 dpi—scanning 1,200 x 1,200 dpi (maximum)—printing
    Zoom range 25%–400% in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 87%, 82%, 71%, 61%, 50%, 25%
    Duplex copy Simplex to duplex, duplex to duplex—with ARDF, book to duplex, front and back to duplex
    Book copy Booklet, magazine, layout and booklet
  • Connectivity
    Interfaces - standard

    Mainframe
    10Base-T/100Base-Tx (Ethernet)
    1000Base-T (Gigabit Ethernet)
    USB Host Type A—2 ports
    USB Type B—1 port

    Smart Operation Panel
    Bluetooth 5.21
    USB Host Type A—USB Flash memory
    USB Host Type A—optional 1 port for USB keyboard

    1
    —Cannot be used for printing

    Interfaces - optional IEEE 802.11 a/b/g/n/ac Interface Unit Type M52
    Device Server Option Type M52 (additional Ethernet/Gigabit Ethernet port)
    Network protocols - standard TCP/IP (IPv4, IPv6)
  • Media Handling
    Standard input capacity (sheets) 1,200
    Maximum input capacity (sheets) 2,300
    Standard output capacity (sheets) 500
    250—B4 or larger
    Maximum output capacity (sheets) 1,625
    Paper input configuration - standard 2 x 550-sheet paper trays, 100-sheet bypass tray, 100-sheet ARDF, duplex unit
    Paper output configuration - standard 500-sheet face-down internal output tray
    Supported media

    Tray 1
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper

    Tray 2
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper, envelope

    Optional trays
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper

    Bypass tray
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper, label paper

    Maximum paper size SRA3
    Media weight (g/m2) 52–300
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 701 x 913 mm
    Weight—mainframe 89.7 kg
  • Configuration
    Functions Copy, print, scan, optional fax
    Colour Yes
    HDD 256 GB SSD
    Memory - standard 6 GB—2 GB mainframe + 4 GB Smart Operation Panel
    Operation panel 10.1" Smart Operation Panel
  • Environmental features
    Power source  220–240 V, 50/60 Hz—Asia Pacific
    110 V, 60 Hz—Taiwan 
     Power consumption  1,700 W or less—maximum power, Asia Pacific
    1,584 W or less—maximum power, Taiwan
    411.8 W—operating power, black and white
    465.3 W—operating power, colour
    37.7 W—Ready Mode 
    0.3 W—Energy Saver Mode (Sleep Mode)
     Typical Electricity Consumption (TEC)  0.20 kWh
     Warm-up time  

    24 seconds

     Recovery time  

    From Energy Saver Mode
    6.6 seconds

     Green labels  The Thai Green Label Scheme
     Other environmental features  Eco-friendly indicator, Energy Saver Timer, System Reset Timer
  • Software and solutions
    Standard @Remote Embedded
    Web Image Monitor
    Optional Streamline NX V3
    GlobalScan NX
    Enhanced Locked Print NX
    Card Authentication Package
    Mobile apps RICOH Smart Device Connector
  • Supported operating environments
    Windows  PCL 5c, PCL 6, and PostScript 3 
    Windows 8.1
    Windows 10
    Windows Server 2012
    Windows Server 2012 R2
    Windows Server 2016
    Windows Server 2019
    Windows Server 2022 
     Macintosh  MacOS v10.15 or later—PostScript 3 only
     Unix  PCL 5c, PostScript 3
    Sun Solaris, HP-UX, SCO OpenServer, Red Hat Linux, IBM AIX
     SAP  PCL 5c
    R/3, S/4
  • Security features
    Encryption SSD, PDF, Secure print, WEP, WPA Authentication password Encryption of data sent via Scan to email and Fax forwarding (S/MIME)
    Authentication 802.1x wired authentication Administrator authentication IEEE 802.11i security (WPA2) IPv6 Quota setting User authentication—Windows and LDAP via Kerberos, basic, user code WiFi Protected Setup (WPS) support
  • Fax features
    Fax types G3 fax, Internet fax (T.37), IP fax (T.38), LAN-Fax, Paperless fax, Direct SMTP fax
    Fax circuit PSTN, PBX
    Fax compatibilty ITU-T (CCITT), G3—maximum 3 lines
    Fax modem speed 2,400 bps–33.6 Kbps—G3, standard with automatic shift down
    Fax compression methods MH, MR, MMR, JBIG
    Fax resolution

    Standard mode
    200 x 100 dpi—8 x 3.85 lines/mm

    Detail mode

    200 x 200 dpi—8 x 7.7 lines/mm

    Super Fine mode
    400 x 400 dpi—8 x 15.4 lines/mm
    400 x 400 dpi—16 x 15.4 lines/mm

    Note: Super Fine mode is supported with the optional SAF memory.

    G3 fax transmission speed 3 seconds approximately—JBIG, ITU-T No. 1 chart, TTI off, memory transmission
    3 seconds approximately—MMR, ITU-T No. 1 chart, TTI off, memory transmission
    Fax SAF memory capacity Standard
    4 MB—approximately 320 pages

    With optional SAF memory

    60 MB—approximately 4,800 pages
    Fax memory backup 1 hour
    Quick dials 2,000 numbers
  • Scan feautures
    Scan speed Via ARDF 80 ppm—200 x 200 dpi, 300 x 300 dpi
    Scan methods Scan to USB, Scan to email, Scan to folder, Scan to URL, Scan to MSB, Scan to FTP, Scan to PDF/A, Scan to digitally signed PDF, Scan to searchable PDF Note: Optional OCR unit is required to support scanning to a searchable PDF.
    Colour scanning Standard
    Scan resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi, 1,200 dpi Note:1,200 dpi scanning is supported only with A5 or smaller paper size.
    Scan to file types Single- and multi-page TIFF Single-page JPEG Single- and multi-page PDF, PDF/A Single- and multi-page high-compression PDF
    Scan to email Protocols SMTP gateway, TCP/IP, POP, IMAP 4 Authentication SMTP authentication, POP before SMTP authentication Scan resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi Scan to email file types Single-page TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF Multi-page TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF Note: Optional OCR unit is required to support scanning to a searchable PDF.
    Scan to folder Protocols SMB, FTP Resolution 100 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi Search for client folders SMB—browsing directly to the designated folder FTP—by folder name Scan to folder file types Single-page TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF Multi-page TIFF, PDF (default), PDF/A, high-compression PDF, encrypted PDF, searchable PDF Note:Optional OCR unit is required to support scanning to a searchable PDF.
    TWAIN scanning Scan mode Standard, Photo, OCR, Filing Note: Optional OCR unit required for OCR scanning. Scan resolution 100–1,200 dpi Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
  • Print features
    Print speed colour 20 ppm
    Print speed black and white 20 ppm
    First print time 4.5 seconds black and white, 7.0 seconds colour
    Print resolution

    1,200 x 1,200 dpi

    Page description languages (PDLs)

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation, PDF Direct emulation

    Optional
    Genuine Adobe PostScript 3, PDF Direct from Adobe

    Printer drivers

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation

    Optional
    Genuine Adobe PostScript 3

    Duplex printing Standard
    Mobile printing Yes
  • Copy features
    Copy speed 20 cpm
    First copy time 5.1 seconds—black and white
    7.4 seconds—colour
    Copy resolution 100, 200, 300, 400, 600 dpi—scanning
    1,200 x 1,200 dpi (maximum)—printing
    Zoom range 25%–400% in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 87%, 82%, 71%, 61%, 50%, 25%
    Duplex copy Simplex to duplex, duplex to duplex—with ARDF, book to duplex, front and back to duplex
    Book copy Booklet, magazine, layout and booklet
  • Connectivity
    Interfaces - standard

    Mainframe
    10Base-T/100Base-Tx (Ethernet)
    1000Base-T (Gigabit Ethernet)
    USB Host Type A—2 ports
    USB Type B—1 port

    Smart Operation Panel
    Bluetooth 5.21
    USB Host Type A—USB Flash memory
    USB Host Type A—optional 1 port for USB keyboard

    1
    —Cannot be used for printing

    Interfaces - optional IEEE 802.11 a/b/g/n/ac Interface Unit Type M52
    Device Server Option Type M52 (additional Ethernet/Gigabit Ethernet port)
    Network protocols - standard TCP/IP (IPv4, IPv6)
  • Media Handling
    Standard input capacity (sheets) 1,200
    Maximum input capacity (sheets) 2,300
    Standard output capacity (sheets) 500
    250—B4 or larger
    Maximum output capacity (sheets) 1,625
    Paper input configuration - standard 2 x 550-sheet paper trays, 100-sheet bypass tray, 100-sheet ARDF, duplex unit
    Paper output configuration - standard 500-sheet face-down internal output tray
    Supported media

    Tray 1
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper

    Tray 2
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high gloss coated paper, coated paper, envelope

    Optional trays
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper

    Bypass tray
    Plain paper (paper type not displayed), recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, high-gloss coated paper, envelope, coated paper, label paper

    Maximum paper size SRA3
    Media weight (g/m2) 52–300
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 701 x 913 mm
    Weight—mainframe 89.7 kg
  • Configuration
    Functions Copy, print, scan, optional fax
    Colour Yes
    HDD 256 GB SSD
    Memory - standard 6 GB—2 GB mainframe + 4 GB Smart Operation Panel
    Operation panel 10.1" Smart Operation Panel
  • Environmental features
    Power source 100–240 V, 50–60 Hz
    Power consumption Without optional controller
    300 W—max brightness
    180 W—typical
    0.5 W or less—standby
    Environmental standards REACH
    ErP Lot 5
    EU battery (2006/66/EC)
    EU packaging (94/62/EC)
    WEEE
    RoHSEN63000 (CE marking)
    Safety standards EN62368-1 (CE marking)
    EN62368-1 (TUV)
    IEC60950-1 / IEC62368-1 (CB attestation)
    TH-A (Thailand)
    Electromagnetic Compatibility (EMC) standards EN55035, EN55032, EN61000-3-2, EN61000-3-3 (CE marking)
    AS / NZS CISPR32 (C-Tick) (Australia / NZ)
    HK EMC (Hong Kong)
    EN62311 (CE marking)
    Wireless LAN standards EN300328 / EN301893 (CE marking)
    EN301489-1 / EN301489-17 (CE marking)
    EN300328 / EN301893 (RCM) (Australia / NZ)
    EN301489-1 / EN301489-17 (RCM)(Australia / NZ)
    Operating environment

    Temperature
    0–32ºC—operating
    -10–50ºC—storage

    Humidity
    20–80%—operating
    15–80%—storage

  • Supported operating environments
    Windows

    System
    Windows 10 Professional, 64-bit
    *This device meets the system requirements to install Windows 11.

    Multi-touch
    Windows 7, 8, 10

    Single-touch
    Windows XP

    Macintosh Single-touch
    Mac OS X
    Supported languages On-screen display
    Japanese, English, French, German, Italian, Spanish, Dutch, Danish, Russian, Polish, Swedish, Norwegian, Finnish, Brazilian Portuguese, Czech, Romanian, Greek, Turkish, Simplified Chinese
  • Connectivity
    Interfaces - standard

    Rear
    2 x HDMI 2.0 in
    1 x DisplayPort in
    1 x VGA in
    1 x Audio in
    2 x LAN—10/1000 Base-T,100 Base-TX (to OPS),10/1000 Base-T (to Android)
    1 x USB 2.0 Type A
    2 x USB 3.0 Type A
    1 x USB 3.0 Type B—touch interface
    1 x Mic in
    1 x SPDIF in
    1 x HDMI 2.0 out
    1 x Audio out
    1 x RS-232 in

    Front
    1 x USB Type C
    2 x USB 3.0 Type A
    1 x USB 3.0 Type B—touch interface for HDMI
    1 x HDMI 2.0 in—HDCP compliant

    Interfaces - optional With Ricoh IWB Controller OP-5 Type 2
    10Base-T/100Base-Tx/1000Base-T
    Bluetooth—embedded
    IEEE 802.11 ac/a/b/g/n/ax
    1 x HDMI output
    2 x USB 3.0 Type A
    2 x USB 2.0 Type A
    1 x USB Type C
    1 x 3.5 mm mic jack
    1 x 3.5 mm headphone jack
  • Touch System
    Touch technology Infrared touch frame
    Touch points 20
    Touch resolution 32,768 x 32,768—interpolated
    Touch output HID Standard, USB 2.0 full speed
    Touch panel cover glass 3.2 mm toughened glass
  • Optical and audio systems
    Panel size 65 inches
    Backlight D-LED
    Effective display area 1,428.48 x 803.52 mm
    Resolution 3,840 x 2,160 pixels
    Colour reproduction 1.07 billion colours (8-bit + Frame rate control)
    Brightness 350 cd/m2—typical
    Contrast 1200:1
    Pixel pitch 0.372 mm
    Response speed 8 ms
    Viewing angle HV 178 degrees
    Audio Rear
    1 x 3.5 mm mic and other audio source in
    1 x 3.5 mm audio out
    1 x SPDIF
    Video

    Rear
    2 x HDMI 2.0 in
    1 x DisplayPort in
    1 x VGA in
    1 x USB 2.0 Type A
    2 x USB 3.0 Type A
    1 x HDMI 2.0 out

    Front
    1 x HDMI 2.0 in

  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 1,512 x 88 x 921 mm
    Weight—mainframe 39 kg
  • Configuration
    What's included

    Touch pen
    2 pcs

    Read this firstandQuick Guide
    In English, French, German, Spanish, Brazilian Portuguese

    Remote controller
    Yes

    Batteries for remote controller
    2 x AAA batteries

    Power cord
    Yes

    USB-C cable
    Yes—2 m

    USB A-B cable
    Yes—3 m

    HDMI 2.0 cable
    Yes—3 m

    Plastic clamp
    2 pcs

  • Environmental features
    Power source 220–240 V, 50–60 Hz
    Power consumption 950 W—Maximum power
    420 W—Operating power
    111 W—Ready Mode
    55 W or less—Low Power Mode
    12.55 W or less—ARDF
    27 W or less—500-sheet paper bank PB2020
    4.0 W—Energy Saver Mode (Sleep Mode)
    Typical Electricity Consumption (TEC) 1.75 kWh
    Warm-up time 33 seconds or less
    Power saving mode 1 minute shift time—Energy Saver Mode (Sleep Mode)
    30 seconds shift time—Low Power Mode
    Recovery time 30 seconds—Energy Saver Mode (Sleep Mode)
    10 seconds—Low Power Mode
  • Software and solutions
    Standard Web Image Monitor
    Optional Printer as a Service (PaaS)
  • Supported operating environments
    Windows Windows Server 2003
    Windows Server 2003 R2
    Windows Server 2008
    Windows Server 2008 R2
    Windows Vista
    Windows 7
    Windows 8
    Windows 8.1
    Windows Server 2012
    Windows Server 2012 R2
  • Scan features
    Scan speed 200 dpi, A4
    15 ipm—black and white
    6 ipm—colour
    Colour scanning Supported
    Scan resolution 100 x 100 dpi, 150 x 150 dpi, 200 x 200 dpi, 300 x 300 dpi, 600 x 600 dpi; default 200 x 200 dpi
    Scan to folder Protocols
    SMB 1.0

    Security
    Not available

    Resolution
    100 x 100 dpi, 150 x 150 dpi, 200 x 200 dpi, 300 x 300 dpi, 600 x 600 dpi; default 200 x 200 dpi

    Search for client folders
    Not available

    Home folder over LDAP
    Not available

    Maximum client folders per send
    1 folder

    Simultaneous transmission
    Not available

    Maximum group addresses
    Not available

    Input file name
    Not available

    Input subject
    Not available

    Scan to folders file size
    1–5 MB

    Scan to folders file types
    Full colour, greyscale
    JPEG, PDF

    Black and white
    TIFF, PDF

    Program user settings

    Not available

    Resend
    Not available
    TWAIN scanning Scan speed—A4 LEF, 200 x 200 dpi
    Black and white, single-sided
    10 ipm

    Colour, single-sided
    5 ipm

    Scan resolution
    75 x 75 dpi, 100 x 100 dpi, 150 x 150 dpi, 200 x 200 dpi, 300 x 300 dpi, 600 x 600 dpi

    Scan mode
    Full colour, greyscale, black and white

    Image adjustment
    Gamma, sharpness, brightness adjustment, contrast, saturation, hue

    Endorse
    Not available

    Stamp originals
    Not available

    Supported Windows operating systems

    Windows Server 2003, R2
    Windows Vista
    Windows Server 2008, R2
    Windows 7
    Windows 8
    Windows 8.1
    Windows Server 2012, R2
  • Print features
    Print speed black and white 20 ppm
    Print resolution 600 x 600 dpi
    Printer drivers DDST (GDI)—optional DDST unit Type M16 is required for network printing and scanning
    Duplex printing Supported
  • Copy features
    Copy speed 20 cpm—A4 LEF
    First copy time 10 seconds or less—A4 LEF, Tray 1
    Copy resolution 300 x 600 dpi—standard mode
    600 x 600 dpi—fine mode
    Zoom range 50%–200%
    Duplex copy Supported
    Book copy Not available
    ID card copy Supported—requires DDST unit Type M16 option
  • Connectivity
    Interfaces - standard USB 2.0
    Interfaces - optional 10Base-T/100Base-Tx (Ethernet)—available with optional DDST unit Type M16
  • Media handling
    Standard input capacity (sheets) 350
    Maximum input capacity (sheets) 1,350
    Standard output capacity (sheets) 250
    Maximum output capacity (sheets) 250
    Paper input configuration - standard 250-sheet paper input tray, 100-sheet bypass tray, duplex unit, 50-sheet ARDF
    Paper output configuration - standard 250-sheet face-down output tray
    Supported media

    Standard paper input tray
    Thin paper, Plain paper 1, Plain paper 2, Recycled paper, Colour paper, Special paper, Middle thick paper, Printed paper, Pre-printed paper, Pre‑punched paper, Letterhead, Bond paper, Cardstock

    Note:Thin paper only for single-sided printing.

    Bypass tray
    Thin paper, Plain paper 1, Plain paper 2, Recycled paper, Colour paper, Special paper, Middle thick paper, Printed paper, Pre-printed paper, Pre‑punched paper, Letterhead, Bond paper, Cardstock, Thick paper 1, Thick paper 2, Label paper, OHP transparencies, Envelope

    Note:Thin paper and Thick Paper 2 only for single-sided printing.

    Paper bank PB2020
    Plain paper 1, Plain paper 2, Recycled paper, Colour paper, Special paper, Middle thick paper, Printed paper, Pre-printed paper, Pre‑punched paper, Letterhead, Bond paper, Cardstock

    Maximum paper size A3
    Media weight (g/m2) 52–216
  • Configuration
    Functions Copy, print, scan
    Colour No
    Memory - standard 256 MB
    Operation panel 4-line LCD
  • Environmental features
    Power source 220–240 V, 50–60 Hz
    Power consumption 1,700 W—full configuration, maximum 600 W—mainframe only 385 W—operating power, black and white 459 W—operating power, colour 37.9 W—Ready Mode 1.2 W—Energy Saver Mode (Sleep Mode)
    Typical Electricity Consumption (TEC) 0.36 kWh
    Warm-up time 30 seconds
    Power saving mode 60 seconds shift time—Energy Saver Mode (Sleep Mode)
    Recovery time 7.4 seconds—from Energy Saver Mode (Sleep Mode)
  • Software and solutions
    Standard @Remote
    Web Image Monitor
    RICOH Scan Utility v3—from a client PC
  • Supported operating environments
    Windows Windows 7
    Windows 8.1
    Windows Server 2012
    Windows Server 2012 R2
    Windows 10
    Windows Server 2016
    Windows Server 2019
    Macintosh OS X Native v10.13 or later—PostScript3 Emulation only
  • Security features
    Authentication IEEE 802.11 security (WEP, WPA)
    IPv6
    WiFi Protected Setup (WPS) support
  • Scan feautures
    Scan speed A4 LEF, 200 dpi, via ARDF
    17 ipm—black and white
    15 ipm—colour
    Scan methods

    Scan to USB/SD, Scan to email, Scan to folder (SMB, FTP)

    Colour scanning Standard
    Scan resolution 100 dpi, 150 dpi, 200 dpi (default), 300 dpi, 600 dpi
    Scan to file types

    Single page
    TIFF (black and white only), JPEG (greyscale), PDF

    Multi page
    TIFF, PDF

    Scan to email Protocols
    SMTP

    Authentication

    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 150 dpi, 200 dpi (default), 300 dpi, 600 dpi

    Scan to email file types
    Colour, greyscale
    JPG, PDF

    Black and white
    TIFF, PDF
    Scan to folder

    Protocols
    SMB

    Security
    LanMan1.0, NTLAN Manager v1,v2, Generic Security Services API

    Resolution
    100 dpi, 150 dpi, 200 dpi (default), 300 dpi, 600 dpi

    Scan to folder file types
    Colour, greyscale
    JPEG, PDF

    Black and white
    TIFF, PDF

    TWAIN scanning Scan mode
    True Colour, Greyscale, Black and White

    Scan resolution
    75–600 dpi
  • Print features
    Print speed colour 20 ppm
    Print speed black and white 20 ppm
    First print time 5.5 seconds black and white, 7.7 seconds colour
    Print resolution 1,200 x 1,200 dpi—1-bit
    Page description languages (PDLs) PCL 6,PostScript3 emulation
    Printer drivers PCL 6, PostScript3 emulation
    Duplex printing Standard
    Mobile printing AirPrint, Mopria®
  • Copy features
    Copy speed 20 cpm
    First copy time 6.5 seconds—black and white
    10.8 seconds—colour
    Copy resolution

    600 x 600 dpi—platen
    300 x 600 dpi, 600 x 600 dpi—ARDF

    Zoom range 25%–400% in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 82%, 71%, 50%, 25%
    Duplex copy Simplex to duplex, duplex to duplex
    ID card copy Supported
  • Connectivity
    Interfaces - standard Mainframe 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet) USB Host Type A—2 ports USB Type B—1 port
    Interfaces - optional IEEE 802.11 a/b/g/n/ac (Wireless LAN)
    Network protocols - standard TCP/IP (IPv4, IPv6)
  • Media Handling
    Standard input capacity (sheets)   650
     Maximum input capacity (sheets)  1,750
     Standard output capacity (sheets)  500
     Maximum output capacity (sheets)  500
     Paper input configuration - standard  550-sheet paper tray, 100-sheet bypass tray, 50-sheet ARDF, duplex unit
     Paper output configuration - standard  500-sheet face-down internal output tray
     Supported media  Standard tray
    Plain paper, recycled paper, colour paper, special paper 1–3, letterhead, preprinted paper, bond paper, card stock, label, back of copied paper, envelope, coated matte, coated glossy

    Bypass tray
    Plain paper, recycled paper, colour paper, special paper 1–3, letterhead, preprinted paper, bond paper, card stock, OHP, label, back of copied paper, envelope, coated matte, coated glossy

    Optional trays
    Plain paper, recycled paper, colour paper, special paper 1–3, letterhead, preprinted paper, bond paper, card stock, label, back of copied paper, envelope, coated matte, coated glossy
     Maximum paper size  A3
     Media weight (g/m2)  52–300
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 685 x 884.5 mm
    Weight—mainframe 82.5 kg
  • Configuration
    Functions Copy, print, scan
    Colour Yes
    Memory - standard 2 GB
    Operation panel 4.3" touchscreen
  • Environmental features
    Power source 220–240 V, 50/60 Hz, 8 A
    Power consumption 1,480 W—maximum operating
    420 W—printing
    93 W—Ready Mode
    23 W—Low Power Mode
    0.97 W—Energy Saver Mode (Sleep Mode)
    19 W or less—ARDF
    Typical Electricity Consumption (TEC) 1,180 Wh
    Warm-up time 19 seconds or less
    Power saving mode 30 minutes—Low Power Mode (default)
    58 minutes—Energy Saver Mode (Sleep Mode) (default)
    Recovery time 10 seconds or less—Low Power Mode
    13 seconds or less—Energy Saver Mode (Sleep Mode)
  • Software and solutions
    Standard Web Image Monitor
  • Supported operating environments
    Windows Windows Server 2008
    Windows Server 2008 R2
    Windows Vista
    Windows 7
    Windows Server 2012
    Windows Server 2012 R2
    Windows 8.1
    Windows 10
    Windows 2016
  • Security features
    Authentication Wireless LAN security (WEP, WPA)
  • Scan feautures
    Scan speed 18 ipm—black and white
    14 ipm—black and white with TWAIN
    6 ipm—colour
    Scan methods Scan to email, Scan to folder (SMB), Scan to USB/SD
    Colour scanning Standard
    Scan resolution 100 x 100 dpi, 150 x 150 dpi, 200 x 200 dpi (default), 300 x 300 dpi, 600 x 600 dpi
    Scan to file types

    Black and white
    Single- and multi-page PDF
    Single- and multi-page TIFF

    Colour
    Single- and multi-page PDF
    Single-page JPEG

    Scan to email

    Protocols
    SMTP gateway, TCP/IP

    Authentication
    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 150 dpi, 200 dpi (default), 300 dpi,600 dpi

    Scan to email file types
    True colour, greyscale
    JPEG, PDF

    Black and white
    TIFF, PDF

    Scan to folder

    Protocols
    SMB

    Security
    LANMan 1.0, NTLM v1/v2, GSS API

    Resolution
    100 dpi, 150 dpi, 200 dpi (default), 300 dpi, 600 dpi

    Search for client folders
    By name and ID

    Scan to folder file types
    True colour, greyscale
    JPEG, PDF

    Black and white
    TIFF, PDF

    TWAIN scanning

    Scan resolution
    75 dpi, 100 dpi, 150 dpi, 200 dpi, 300 dpi, 600 dpi

    Scan mode
    True colour, greyscale, black and white

  • Print features
    Print speed black and white 27 ppm
    First print time 6.5 seconds or less
    Print resolution 600 x 600 dpi
    Page description languages (PDLs) GDI
    Printer drivers DDST
    Duplex printing Standard
    Mobile printing AirPrint, Mopria®
  • Copy features
    Copy speed 27 cpm
    First copy time 6.5 seconds or less—via platen
    12 seconds or less—via ARDF
    Copy resolution 100 x 100 dpi,150 x 150 dpi, 200 x 200 dpi (default), 300 x 300 dpi, 600 x 600 dpi
    Zoom range 25%–400%
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 82%, 71%, 50%, 25%
    Duplex copy Standard
    Book copy Not available
    ID card copy Supported
  • Connectivity
    Interfaces - standard 10Base-T/100Base-Tx/1000Base-T (Gigabit Ethernet)
    USB 2.0 Type B
    Interfaces - optional IEEE 802.11a/b/g/n/ac (Wireless LAN)
    Network protocols - standard TCP/IP
  • Media Handling
    Standard input capacity (sheets) 600
    Maximum input capacity (sheets) 1,600
    Standard output capacity (sheets) 250
    Maximum output capacity (sheets) 250
    Paper input configuration - standard 500-sheet paper input tray, 100-sheet bypass tray, 50-sheet ARDF
    Paper output configuration - standard 250-sheet output tray
    Supported media

    Standard paper input tray
    Thin paper, plain paper 1, plain paper 2, recycled, colour paper, special paper, middle thick paper, prepunched paper, letterhead, bond paper, cardstock

    Bypass tray
    Thin paper, plain paper 1, plain paper 2, recycled, colour paper, special paper, middle thick paper, prepunched paper, letterhead, bond paper, cardstock, thick paper 1, thick paper 2, label paper, OHP, envelope

    Paper banks
    Plain paper 1, plain paper 2, recycled, colour paper, special paper, middle thick paper, prepunched paper, letterhead, bond paper, cardstock

    Note:Thick paper and OHP are only supported from the bypass tray.
    Maximum paper size A3
    Media weight (g/m2) 52–216
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 581 x 639 mm
    Weight—mainframe 39 kg or less
  • Configuration
    Functions Copy, print, scan
    Colour No
    HDD Not available
    Memory - standard 512MB
    Operation panel 4-line LCD
  • Environmental features
    Power source 220–240 V, 50/60 Hz—Asia Pacific
    110 V, 60 Hz—Taiwan
    Power consumption 1,700 W or less—maximum power, Asia Pacific
    1,584 W or less—maximum power, Taiwan
    415.9 W—operating power, black and white
    465.2 W—operating power, colour
    46.2 W—Ready Mode
    0.55 W—Energy Saver Mode (Sleep Mode)
    Typical Electricity Consumption (TEC) 0.7 kWh
    Warm-up time

    21 seconds or less—Quick Mode from main switch

    Power saving mode

    1 minute shift time—Energy Saver Mode (Sleep Mode)

    Recovery time From Energy Saver Mode
    0.5 seconds—to Key Operation Ready Mode
    6.1 seconds—without Human detection sensor, Asia Pacific
    6.6 seconds—without Human detection sensor, Taiwan
    Green labels The Thai Green Label Scheme, Blue Angel Mark (BAM)
    Other environmental features Eco-friendly indicator, On/off timer, Remote Power Off, Default duplex printing, Eco counter, Human detection sensor
  • Software and solutions
    Standard @Remote Embedded
    Web Image Monitor
    Optional @Remote Office
    @Remote Enterprise Pro
    Java SDK
    Card Authentication Package
    Device Software Manager
    Device Manager NX
    Enhanced Locked Print NX
    GlobalScan NX
    Printer Driver Packager NX
    Streamline NX
    Customer Support Application for Smart Operation Panel
    Mobile apps Smart Device Connector
  • Supported operating environments
    Windows PCL 5c, PCL 6, and PostScript 3
    Windows Server 2008
    Windows Server 2008 R2
    Windows 7
    Windows 8.1
    Windows Server 2012
    Windows Server 2012 R2
    Windows 10
    Windows Server 2016
    Macintosh OS X Native v10.11 or later—PostScript 3 only
    Unix Sun Solaris—10
    HP-UX—11.x, 11iv2, 11iv3
    Red Hat Linux—Enterprise, 4.x, 5.x, 6.x
    SCO OpenServer—5.0.7, 6.0
    IBM AIX— 6.1, 7.1, 7.2
    SAP Environment—R/3, S/4
    SAP R/3 Device Type—supported
    Barcode fonts—Code 128, Code 39, Code 93, Codabar, 2 of 5 interleaved/Industrial/Matrix, MSI, USPS, UPC/EAN
    OCR fonts—OCR A, OCR B
  • Security features
    Data Overwrite Security System (DOSS) - Standard Yes
    Encryption HDD, PDF, Secure print, WEP, WPA
    Authentication password
    Encryption of data sent via Scan to email and Fax forwarding (S/MIME)
    Authentication 802.1x wired authentication
    Administrator authentication
    IEEE 802.11i security (WPA2)
    IPv6
    Quota setting
    User authentication—Windows and LDAP via Kerberos, basic, user code
    WiFi Protected Setup (WPS) support
  • Fax features
    Fax types G3 fax, Internet fax (T.37), IP fax (T.38), LAN-Fax, Paperless fax, Direct SMTP fax
    Fax circuit PSTN, PBX
    Fax compatibilty ITU-T (CCITT), G3—maximum 3 lines
    Fax modem speed 2,400 bps–33.6 Kbps—G3, standard with automatic shift down
    Fax compression methods MH, MR, MMR, JBIG
    Fax resolution

    Standard mode
    200 x 100 dpi—8 x 3.85 lines/mm

    Detail mode

    200 x 200 dpi—8 x 7.7 lines/mm

    Super fine mode
    400 x 400 dpi—8 x 15.4 lines/mm
    400 x 400 dpi—16 x 15.4 lines/mm

    Note: Super fine mode is supported with the optional SAF memory.

    G3 fax transmission speed 2 seconds approximately—JBIG, ITU-T No. 1 chart, TTI off, memory transmission
    3 seconds approximately—MMR, ITU-T No. 1 chart, TTI off, memory transmission
    Fax SAF memory capacity Standard
    4 MB—approximately 320 pages

    With optional SAF memory

    60 MB—approximately 4,800 pages
    Fax memory backup 1 hour
    Quick dials 2,000 numbers
  • Scan feautures
    Scan speed

    80 ppm—via ARDF

    Via SPDF
    120 ppm—single-sided, 200 x 200 dpi
    110 ppm—single-sided, 300 x 300 dpi
    240 ppm—duplex, 200 x 200 dpi
    180 ppm—duplex, 300 x 300 dpi

    Scan methods

    Scan to USB/SD, Scan to email, Scan to webmail,Scan to folder (SMB, FTP), Scan to URL, Scan to PDF/A,Scan to searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Colour scanning Standard
    Scan resolution 100 x 100 dpi, 200 x 200 dpi, 300 x 300 dpi,400 x 400 dpi,
    600 x 600 dpi, 1,200 x 1,200 dpi; default 200 x 200 dpi
    Note:1,200 dpi scanning is supported only with Network TWAIN and A5 or smaller paper size.
    Scan to file types Single- and multi-page TIFF
    Single-page JPEG
    Single- and multi-page PDF, PDF/A
    Single- and multi-page high-compression PDF
    Scan to email

    Protocols
    SMTP gateway, TCP/IP, POP, IMAP 4

    Authentication

    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 x 100 dpi, 200 x 200 dpi, 300 x 300 dpi, 400 x 400 dpi,
    600 x 600 dpi; default 200 x 200 dpi

    Scan to email file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note: Optional OCR unit is required to support scanning to a searchable PDF.

    Scan to folder

    Protocols
    SMB, FTP

    Security
    Client folder logon, transmission encryption of logon name and password

    Resolution
    100 x 100 dpi, 200 x 200 dpi, 300 x 300 dpi, 400 x 400 dpi,
    600 x 600 dpi; default 200 x 200 dpi

    Search for client folders
    SMB—browsing directly to the designated folder
    FTP—by folder name

    Scan to folder file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Multi-page
    TIFF, PDF, PDF/A, high-compression PDF, encrypted PDF, searchable PDF

    Note:Optional OCR unit is required to support scanning to a searchable PDF.

    TWAIN scanning Scan mode
    Standard, Photo, OCR, Filing

    Scan resolution
    100 x 100 dpi–1,200 x 1,200 dpi
    Note: 1,200 dpi scanning is supported only with A5 or smaller paper size.
  • Print features
    Print speed colour 20 ppm
    Print speed black and white 20 ppm
    First print time 5.5 seconds black and white, 7.7 seconds colour
    Print resolution

    1,200 x 1,200 dpi—2-bit

    Note:Print speed will be slower when printing at 1,200 x 1,200 dpi.

    Page description languages (PDLs)

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation, PDF Direct emulation

    Optional
    Genuine Adobe PostScript 3, PDF Direct from Adobe, XPS Direct Print, PictBridge

    Printer drivers

    Standard
    PCL 5c, PCL 6,PostScript 3 emulation

    Optional
    Genuine Adobe PostScript 3

    Duplex printing Standard
    Mobile printing Yes
    Print from USB/SD
    Supported
  • Connectivity
    Interfaces - standard

    Mainframe
    10Base-T/100Base-Tx (Ethernet)
    1000Base-T (Gigabit Ethernet)
    USB Host Type A—2 ports
    USB Type B—1 port

    Smart Operation Panel
    IEEE 802.11 b/g/n (Wireless LAN)1
    Bluetooth2
    SD card slot—SDHC memory card
    USB Host Type A—USB Flash memory
    USB Host Type A—1 port for USB keyboard2
    USB Host Type mini B—for NFC card reader2
    microSD card slot—ROM storage expansion2
    NFC tag2

    1—Limited printing for a peer-to-peer mobile device via RICOH Smart Device Connector
    2—Cannot be used for printing

    Interfaces - optional IEEE 1284/ECP
    IEEE 802.11a/g/n (Wireless LAN)
    USB device server (additional Ethernet/Gigabit Ethernet port)
    Network protocols - standard TCP/IP (IPv4, IPv6)
  • Copy features
    Copy speed   20 cpm
     First copy time  5.1 seconds—black and white
    7.4 seconds—colour
     Copy resolution  

    600 x 600 dpi—4-bit

    Note: Copy resolution when scanning.

     Zoom range  25%–400% in 1% steps
     Enlargement ratios  115%, 122%, 141%, 200%, 400%
     Reduction ratios  93%, 82%, 75%, 71%, 65%, 50%, 25%
     Duplex copy  Simplex to duplex, duplex to duplex—with ARDF, book to duplex, front and back to duplex
     Book copy  Booklet, magazine, layout and booklet
     ID card copy  Supported
     User codes  1,000 user codes
     
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 587 x 685 x 788 mm
    Weight—mainframe 82.5 kg or less
  • Media Handling
    Standard input capacity (sheets) 1,200
    Maximum input capacity (sheets) 2,300
    Standard output capacity (sheets) 500
    250—B4 or larger
    Maximum output capacity (sheets) 1,625
    Paper input configuration - standard 2 x 550-sheet paper trays, 100-sheet bypass tray, duplex unit
    Paper output configuration - standard 500-sheet face-down internal output tray
    Supported media

    Tray 1
    Plain paper, recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, glossy coated paper, coated paper, normal paper, middle thick, thick paper 1, thick paper 2, thick paper 3, thick paper 4

    Tray 2
    Plain paper, recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, glossy coated paper, coated paper, envelopes, normal paper, middle thick, thick paper 1, thick paper 2, thick paper 3, thick paper 4

    Paper banks
    Plain paper, recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, glossy coated paper, coated paper, envelopes, normal paper, middle thick, thick paper 1, thick paper 2, thick paper 3, thick paper 4

    Bypass tray
    Plain paper, recycled paper, special paper 1–3, colour paper, letterhead, cardstock, pre-printed paper, bond paper, glossy coated paper, coated paper, envelopes, label paper, OHP, thin paper, normal paper, middle thick, thick paper 1, thick paper 2, thick paper 3, thick paper 4

    Maximum paper size SRA3
    Media weight (g/m2) 52–300
  • Configuration
    Functions Copy, print, scan, optional fax
    Colour Yes
    HDD 320 GB
    Memory - standard 2 GB
    Memory - optional 4 GB—maximum 4 GB
    Operation panel 10.1-inch tilting colour WSVGA Smart Operation Panel
  • Environmental features
    Power source 220–240 V, 16 A, 50/60 Hz
    Power consumption 3,840 W or less—maximum power
    60 W or less—SPDF
    Power consumption—options 50 W or less—4,400-sheet LCT RT4060 (A4)
    85 W or less—2,200-sheet LCT RT5140 (A3)
    1,000 W or less—4,400-sheet Vacuum-Feed LCT RT5120
    70 W—Multi-Bypass Tray BY5020
    83.6 W—Bridge Unit BU5030 for Vacuum-Feed LCT RT5120
    67 W—Finisher SR5090
    15 W—Output Jogger Unit Type S11
    67 W—Booklet-Finisher SR5100
    150 W—Finisher SR5110
    150 W—Booklet Finisher SR5120
    75 W—Trimmer Unit TR5050, average
    250 W—Trimmer Unit TR5050, maximum
    95 W—Cover Interposer CI5040, excluding peak consumption
    43 W or less—Cover Interposer CI5050
    144 W—High-Capacity Stacker SK5040
    30 W—Decurl Unit DU5080
    200 W or less—Buffer Pass Unit Type S9
    240 W—Multi-Folding Unit FD5020
    Typical Electricity Consumption (TEC) 5,813 Wh
    Warm-up time 120 seconds or less
    Sound power level Mainframe
    33.7 dB(A)—Standby
    68.7 dB(A)—Operating

    Full system
    73.5 dB(A)—Operating
    Emission levels 0.2 mg/h—dust, black and white
    0.24 mg/h—dust, colour
    0.26 mg/h—ozone, black and white
    1.5 mg/h—ozone, colour
    0.039 mg/h—styrene, black and white
    0.067 mg/h—styrene, colour
    Reduction of environmentally sensitive materials 100% lead-free solder used in PCBs—lead
    0%—PVC
    100% chrome-free steel plates—hexavalent chromium
    0%—cadmium
    0%—PBB/PBDE
    Safety standards EN60950-1
    IEC60950-1
    CNS14336
    Electromagnetic Compatibility (EMC) standards EN55022 Class A
    EN55024
    EN55011
    EN61000-3-2, EN61000-3-3
    EN301489-1
    AS/NZS CISPR22, CISPR11
    CNS13438
    Identification of plastic components All plastic components that weigh more than 25 g are identified in accordance with ISO 11469 standards.
    Laser standards EN60825-1
  • Software and solutions
    Standard

    Device management and monitoring
    @Remote
    Device Manager NX
    Device Software Manager
    Web Image Monitor

    Workflow solutions
    Ricoh
    Streamline NX
    Global Scan NX
    Integrated Cloud Environment
    Ricoh Smart Integration
    ProcessDirector
    TotalFlow Prep
    TotalFlow Production Manager
    TotalFlow BatchBuilder

    Third party
    EFI DigitalStoreFront
    EFI Colour Profiler Suite
    EFI Fiery Graphic Arts Pro
    EFI Fiery ColorRight
    EFI Fiery Automation
    EFI DirectSmile
    EFI Fiery Central
    CGS/ORIS Lynx & Evaluate
    Objectif Lune

    Software development
    Device SDK

  • Supported operating environments
    Windows 7, 8.1, 10, Server 2008, Server 2008 R2, Server 2012, Server 2012 R2, Server 2016, Server 2019
    Citrix support Citrix XenDesktop 7.0/7.1, Citrix XenApp 7.5 and later
    Macintosh v10.11 or later
    Unix Sun Solaris, HP-UX, Red Hat Linux, SCO Open Server, IBM AIX
    SAP R/3, S/4
  • Security features
    Unauthorised copy protection Copy
    Data Overwrite Security System (DOSS) - Standard Yes
    Data Overwrite Security System (DOSS) - Optional Data Overwrite Security (DOS) unit Type M19
    Encryption HDD, PDF, Secure print encryption
    Authentication IEEE 802.11i.w security
    IPv6
    Network user authentication
    Other security features IP filtering—access control
    IPsec communication
    SNMPv3 support
    SMTP over SSL communication
    Secure Sockets Layer (SSL)
    Transport Layer Security (TLS)
    PDF digital signature
  • Scan features
    Scan speed

    A4 LEF, black and white, via SPDF
    Simplex

    120 ipm—200 x 200 dpi, 300 x 300 dpi, 1-bit

    Duplex
    220 ipm—200 x 200 dpi, 300 x 300 dpi, 1-bit

    A4 LEF, colour, via SPDF
    Simplex

    120 ipm—200 x 200 dpi, 300 x 300 dpi, 4-bit

    Duplex
    220 ipm—200 x 200 dpi, 300 x 300 dpi, 4-bit

    Scan methods Scan to email
    Colour scanning Standard
    Scan mode

    Black and white
    Text, text/line art, text/photo, photo, greyscale

    Colour—24-bit
    Text/photo, glossy photo, Automatic Colour Selection

    Scan resolution 100 dpi, 150 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi, 1,200 dpi
    Scan area 297 mm—main scan
    432 mm—sub-scan
    Image density adjustment Automatic selection, manual selection—7 levels
    Scan to file types Single- and multi-page TIFF
    Single-page JPEG
    Single- and multi-page PDF, PDF/A
    Single- and multi-page high compression PDF
    Scan to file type support Single- and multi-page TIFF
    Black and white 1-bit—MH, MR, MMR—compression on
    Black and white 1-bit, black and white greyscale, full colour—compression off

    Single-page JPEG
    Black and white greyscale, full colour—compression on

    Single- and multi-page PDF, PDF/A
    Black and white 1-bit—MH, MR, MMR, JBIG2
    Black and white greyscale JPEG, full colour JPEG—compression on
    Black and white 1-bit, black and white greyscale, full colour—compression off

    Single- and multi-page high compression PDF
    Black and white greyscale, full colour—JPEG, JPEG 2000—compression on
    Scan to email

    Authentication
    SMTP authentication, POP before SMTP authentication

    Scan resolution
    100 dpi, 150 dpi, 200 dpi (default), 300 dpi, 400 dpi, 600 dpi

    Scan to email file types
    Single-page
    TIFF, JPEG, PDF, PDF/A, High Compression PDF, Encrypted PDF, Searchable PDF

    Multi-page
    TIFF, PDF, PDF/A, High Compression PDF, Encrypted PDF, Searchable PDF

    Note:Optional OCR unit is required to support scanning to a searchable PDF.

    Scan to email—other features

    Scan to email size
    128–102,400 KB—with restriction
    700 MB—without restriction

    Maximum email addresses per send
    500—from HDD
    100—direct input
    100—via LDAP

    Email addresses stored in HDD
    Maximum email addresses—2,000
    Maximum registered group addresses—100 groups, 500 addresses per group
    Maintain email addresses—via operation panel, SmartDeviceMonitor for Admin,Web Image Monitor
    Search method—by name, email address

    Body message
    Manual input—maximum 80 characters over 5 lines via operation panel
    User pre-registered—maximum 400 characters, 80 characters over 5 lines via operation panel
    Preset message—This e-mail includes attached file sent from .

    Input subject
    Manual input—maximum 128 characters via operation panel
    User pre-registered—maximum 20 characters via operation panel

    Input of destination email address via operation panel
    100 maximum destinations per job

    LDAP search
    Supported

    Input file name
    Supported

    Simultaneous transmission
    Maximum 550 destinations

    Attention
    To, Cc, Bc

    Program registration
    Up to 25 programs

    Divide and send
    Divide by page or size; default divide by size

    Note:If the sent file is larger than the email size restriction, it will be divided into multiple sends. The size restrictions of the email recipient may also impact the send.

    Resend
    Yes—default/No

    Other scan features sRGB support, Image rotation,SADF/batch mode, Mixed size mode, Reduce/enlarge scanning, Split scan from booklet
  • Copy features
    Copy speed 65 cpm—A4 LEF
    First copy time 9.2 seconds or less—black and white
    10.6 seconds or less—colour
    Copy resolution 600 x 600 dpi—4 bit
    Quantity selection Up to 9,999
    Copy reservations 8 jobs
    Job presets 8 jobs
    Job programs 25 programs
    Zoom range 25%–400%, in 1% steps
    Enlargement ratios 115%, 122%, 141%, 200%, 400%
    Reduction ratios 93%, 87%, 82%, 71%, 61%, 50%, 25%
    Image density adjustment Automatic selection, manual selection—7 levels
    Image density adjustment Automatic or manual selection
    Copy modes Auto text and photo separation (default)—printed/glossy/copied, Photo—printed/glossy/copied
    Text, Map, Generation, Highlight pen, Inkjet
    Colour mode

    Options
    Black and white (default), single colour, two colour, full colour, Automatic Colour Selection

    Single colour
    12 colours x 4 density—single colour preset; default red
    15 colours x 4 density—user selection

    Two colour
    Black and other colour, red and black

    Paper selection

    Default
    Auto Paper Selection (APS)

    Standard
    1st tray, 2nd tray, 3rd tray, bypass tray

    Optional
    A4 LCT RT4060, A3 LCT RT5140

    Duplex copy Simplex, duplex, simplex to duplex, duplex to duplex, book to duplex, front and back cover to duplex, duplex to simplex
    Book copy Booklet, magazine, layout and booklet
    Series copy Book to simplex, duplex to simplex
    Combine copy 2, 4, or 8 pages into 1 simplex sheet
    1, 2, or 4 duplex pages into 1 simplex sheet
    4, 8, or 16 pages into 1 duplex sheet
    2, 4, or 8 duplex pages into 1 duplex sheet
    Interrupt copy Supported
    Auto tray change Supported; default off
    Paper library Supported
    Copy prevention pattern Supported
    Bates numbering Supported
    User codes 1,000 user codes, 8 digits in each code
    Centring Supported
    Cover sheet Front and back covers—copy or blank; default copy
    Slip sheet Supported—user can choose to copy or not copy to slip sheet
    Chaptering Supported—up to 100 chapters
    Stapling Supported—with finisher
    Punch Supported—with finisher
    Electronic stacking Supported—with finisher
    Electronic sorting Rotate sort—supported
    Shift sort—supported without finisher
    Without shift sort—supported without finisher
    Margin/erase adjustment Margin and scan position—0–30 mm in 1 mm steps
    Creep—0–99 mm in 1 mm steps
    Erase centre and border—2–99 mm in 1 mm steps
    Image adjustment Sharpen/soften—7 levels
    Contrast—9 levels
    Background density—9 levels
    Under Colour Removal (UCR)—9 levels
    Text and photo separation sensitivity—9 levels
    Colour erase sensitivity—5 levels
    Image creation Repeat, double copy, mirror, positive/negative, erase inside—5 parts, erase outside—1 part
    Colour creation Colour conversion—supported—maximum 4 colours, selectable from 12 preset colours, black, or 15 user colours
    Colour erase—supported
    Colour overlay—supported
    Stamps User stamp—4 stamps
    Date stamp—5 styles
    Page numbering—6 styles
    Preset stamp—8 stamps
    Bates stamping—9 digits without zero suppression
    Image rotation Supported
    Other copy features Automatic Colour Calibration (ACC), Colour Balance Adjustment, Colour Balance Program, Auto start, Sample copy, Unauthorised copy prevention
  • Connectivity
    Interfaces - standard

    Mainframe
    10Base-T/100Base-Tx/1000Base-T (Gigabit Ethernet)
    USB Type A—2 ports on rear and 1 port on operation panel
    USB Type B
    SD slot—on operation panel

    Smart Operation Panel
    IEEE 802.11 b/g/n (Wireless LAN)1
    Bluetooth 4.22
    SD Card Slot—SDHC memory card
    USB Host Type A—USB Flash memory
    USB Host Type A—1 port for USB keyboard (optional)2
    USB Host Type mini B—for NFC card reader (optional)2
    microSD card slot—ROM storage expansion2
    NFC Tag2

    1—Limited printing for a peer-to-peer mobile device via RICOH Smart Device Connector
    2—Cannot be used for printing

    Interfaces - optional

    IEEE 1284
    Wireless LAN (IEEE 802.11 a/b/g/n)
    Copy Connector Type M25

    Note:Wireless LAN cannot be used with Bluetooth at the same time.

    Network protocols - standard TCP/IP (IPv4, IPv6)
    MIB support

    Standard
    MIB-II (RFC1213)
    Host Resources MIB (RFC1514)
    Printer MIB (RFC1759)
    Printer Port Monitor MIB

    Private
    Ricoh original MIB

  • Media Handling
    Standard input capacity (sheets) 3,850
    Maximum input capacity (sheets) 8,500
    Standard output capacity (sheets) Not available
    Maximum output capacity (sheets) 4,500
    Paper input configuration - standard 2,500-sheet tandem input tray, 2 x 550-sheet paper input trays, 250-sheet bypass tray, 220-sheet SPDF, duplex unit
    Paper input configuration - optional 4,400-sheet Vacuum-Feed LCT RT5120,4,400-sheet LCT RT4060 (A4), 2,200-sheet LCT RT5140 (A3), 50-sheetMulti-Bypass Banner Sheet Tray Type S6, 500-sheetMulti-Bypass Tray BY5020, 500-sheetMulti-Bypass Banner Sheet Tray Type S9, 730-sheet Vacuum-Feed Banner Sheet Tray Type S9, 2,500-sheet B4 Paper Size Tray Type M2 for LCT RT4060 (A4), 250-sheetBanner Sheet Guide Tray for A3 LCT Type S13, 1,000-sheetA3 Tray Type M26 for tandem tray (internal)
    Paper output configuration - optional 500-sheet Copy Tray Type M42, 3,000-sheet Finisher SR5090, 2,000-sheet Booklet Finisher SR5100, 4,500-sheet Finisher SR5110, 3,500-sheet Booklet Finisher SR5080, Timmer Unit TR5050, 50-sheet SR4000 Series Banner Sheet Output Tray Type S6, 200-sheetSR5000 Series Banner Sheet Output Tray Type S6, Decurl Unit DU5080, Buffer Pass Unit Type S6, Multi-Folding Unit FD5020, 200-sheetCover Interposer CI5050, 400-sheetCover Interposer CI5040, 5,250-sheetHigh-Capacity Stacker SK5040
    Paper output configuration - 3rd Party Plockmatic PBM 350e/PBM 500e, GBC StreamPunch Ultra, GBC e-Wire Binder
    Supported media Standard paper input tray 1, LCT RT4060 (A4) Plain paper, recycled paper, letterhead, pre-printed paper, pre-punched paper Standard paper input trays 2 and 3 Plain paper, recycled paper, letterhead, pre-printed paper, pre-punched paper, tab stock, envelope Bypass tray, LCT RT5140 (A3), duplex unit Plain paper, recycled paper, letterhead, pre-printed paper, pre-punched paper, OHP (transparencies), tab stock, translucent paper, label, envelope, glossy/matte coated paper
    Maximum paper size 13" x 19.2"
    Media weight (g/m2) 52.3–360
    Limitless paper supply Supported
  • Supply yields
    Supply yields

    31,000 copies per 1,020 g bottle—black
    26,000 copies per 1,020 g bottle—cyan
    26,000 copies per1,099 g bottle—magenta
    26,000 copies per 1,020 g bottle—yellow

    110,000 sheets per bottle—waste toner bottle

    Note:All toner yields are based on A4/8.75% coverage, 20 pages per job. Waste toner bottle yield is based on A4/8.75% coverage, 20 pages per job, 80% duplex, and 60% colour ratio.

    5,000 staples per Type X cartridge for finisher SR5110/SR5120—normal staple
    5,000 staples per Type V cartridge for finisher SR5090/SR5100—normal staple
    2,000 staples per Type W cartridge for booklet finisher SR5100—saddle stitch staple
    5,000 staples per Type U cartridge for bookletfinisher SR5120—saddle stitch staple

    5 cartridges per Type X refill for finisher SR5110/SR5120—normal staple
    3 cartridges per Type V refill for finisher SR5090/SR5100—normal staple
    4 cartridges per Type W refill for bookletfinisher SR5100—saddle stitch staple
    2 cartridges per Type T refill for bookletfinisher SR5120—saddle stitch staple

  • Reliability
    Average monthly volume 20,000 prints per month
    Average monthly statement 10,000–80,000 prints per month (recommended)
    Max monthly volume 150,000 prints
    Machine life 9,000,000 prints or 5 years, whichever comes first
    Duty cycle 450,000 prints per month
    Colour ratio 60%
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 799 x 880 x 1,648 mm
    Physical dimensions (WxDxH)—other 587 x 520 x 175 mm—SPDF
    352 x 540 x 625 mm—4,400-sheet LCT RT4060 (A4)
    869 x 730 x 658 mm—2,200-sheet LCT RT5140 (A3)
    1,054 x 730 x 1,000 mm—4,400-sheet Vacuum-Feed LCT RT5120
    1,290 x 730 x 1,000 mm—4,400-sheet Vacuum-Feed LCT RT5120with optional vacuum-feed banner sheet tray attached
    690 x 561 x 210 mm—Multi-Bypass Tray BY5020
    1,090 x 561 x 210 mm—Multi-Bypass Banner Sheet Tray Type S9 when attached to Multi-Bypass Tray BY5020
    1,290 x 730 x 1,302 mm—Multi-Bypass Banner Sheet Tray Type S9 with the cover open
    225 x 730 x 1,000 mm—Bridge Unit BU5030 for Vacuum-Feed LCT RT5120
    1,290 x 730 x 1,000 mm—Vacuum-Feed Banner Sheet Tray Type S9when attached to Vacuum-Feed LCT RT5120
    20 x 514 x 207 mm—A3 Tray Type M26 for internal tandem tray
    350 x 220 x 360 mm—Multi-Bypass Banner Sheet Tray Type S6
    516 x 718 x 135 mm—Banner Sheet Guide Tray Type S13 for A3 LCT
    657 x 730 x 980 mm—Finisher SR5090 with all extendable trays closed
    169 x 539 x 203 mm—Output Jogger Unit Type S11 including jogger operating range
    657 x 730 x 980 mm—Booklet-Finisher SR5100 with all extendable trays closed
    169 x 539 x 203 mm—Output Jogger Unit Type S11 including jogger operating range
    1,113 x 730 x 1,490 mm—Finisher SR5110
    1,334 x 730 x 1,622 mm—Finisher SR5110 with banner sheet option
    1,113 x 730 x 1,490 mm—Booklet Finisher SR5120
    1,334 x 730 x 1,622 mm—Booklet Finisher SR5120 with banner sheet option
    1,115 x 591 x 555 mm—Trimmer Unit TR5050
    740 x 730 x 1,290 mm—Cover Interposer CI5040
    500 x 600 x 600 mm—Cover Interposer CI5050
    900 x 730 x 1,010 mm—High-Capacity Stacker SK5040
    350 x 500 x 170 mm—Copy Tray Type M26
    376 x 885 x 1,140 mm—Decurl Unit DU5080
    330 x 730 x 1,010 mm—Buffer Pass Unit Type S9
    470 x 730 x 1,000 mm—Multi-Folding Unit FD5020
    330 x 740 x 1,010 mm—Bridge Unit Type BU5020
    Weight—mainframe 262 kg or less
    Weight—other 14 kg or less—SPDF
    20 kg or less—4,400-sheet LCT RT4060 (A4)
    83 kg or less—2,200-sheet LCT RT5140 (A3)
    230 kg or less—4,400-sheet Vacuum-Feed LCT RT5120
    20 kg or less—Multi-Bypass Tray BY5020
    3.5 kg—Multi-Bypass Banner Sheet Tray Type S9
    41 kg—Bridge Unit BU5030 for Vacuum-Feed LCT RT5120
    7 kg or less—Vacuum-Feed Banner Sheet Tray Type S9
    11 kg—A3 Tray Type M26 for internal tandem tray
    1.1 kg or less—Multi-Bypass Banner Sheet Tray Type S6
    1.98 kg—Banner Sheet Guide Tray Type S13 for A3 LCT
    38 kg or less—Finisher SR5090
    2 kg or less—Output Jogger Unit Type S11
    53 kg or less—Booklet-Finisher SR5100
    135 kg—Finisher SR5110
    160 kg—Booklet Finisher SR5120
    75 kg—Trimmer Unit TR5050
    50 kg—Cover Interposer CI5040
    12 kg or less—Cover Interposer CI5050
    120 kg or less—High-Capacity Stacker SK5040
    15 kg or less—Roll-away cart forHigh-Capacity Stacker SK5040
    2.2 kg or less—Copy Tray Type M26
    30 kg or less—Decurl Unit DU5080
    90 kg or less—Buffer Pass Unit Type S9
    92 kg or less—Multi-Folding Unit FD5020
    40 kg or less—Bridge Unit Type BU5020
    Minimum space requirements 100 mm—left
    100 mm—rear
    900 mm—right
    400 mm—front
  • Configuration
    Functions Copy, print, scan
    Colour Yes
    Printer controller - standard GWNX
    Printer controller - optional Fiery colour controller E-27B Fiery colour controller E-47B
    HDD 640 GB (320 GB x 2)
    Document server 170 GB HDD capacity—shared with other applications 3,000 maximum stored documents 3,000 pages maximum per document 15,000 pages maximum of all stored documents 1–180 days storage, or no limit
    CPU 1.6 GHz
    Memory - standard 4 GB
    Operation panel 10.1-inch Smart Operation Panel
  • Environmental features
    Power source 220–240 V, 16 A, 50/60 Hz
    Power consumption 5,000 W or less—maximum power
    4 W or less—Energy Saver Mode (Sleep Mode)
    Power consumption—options 1,000 W or less—4,400-sheet vacuum feed LCT RT5120
    150 W or less—3,000-sheet finisher SR5050
    150 W or less—2,500-sheet booklet finisher SR5060
    250 W or less, maximum—Booklet trimmer TR5040
    75 W or less, average—Booklet trimmer TR5040
    150 W or less—4,500-sheet finisher SR5110
    150 W or less—3,500-sheet booklet finisher SR5120
    250 W or less, maximum—Trimmer unit TR5050
    75 W or less, average—Trimmer unit TR5050
    95 W excluding peak consumption—Cover interposer CI5040
    400 W or less—Ring Binder RB5020
    623 W or less—Perfect Binder GB5010
    30 W or less—Decurler unit DU5060
    240 W or less—Multi-purpose folding unit FD5020
    131 W or less—High-capacity stacker SK5040
    200 W or less—Buffer pass unit Type S9
    Warm-up time 300 seconds or less—mainframe
    380 seconds or less—Perfect Binder GB5010
    Sound power level Mainframe
    73 dB—standby
    81 dB—operating

    Full configuration
    73 dB—standby
    83 dB—operating
    Emission levels 4.0 mg/h or less—dust
    4.0 mg/h or less—ozone
    1.8 mg/h or less—styrene
    2.0 mg/h or less—formaldehyde
    Reduction of environmentally sensitive materials RoHS
    100% lead-free solder used in PCBs—lead
    0%—PVC
    100% chrome-free steel plates—hexavalent chromium
    0%—cadmium
    0%—PBB/PBDE
    Energy saving standards Energy Star v2.0—with GWNX, Ricoh TotalFlow Print Server, and EFI Fiery controllers
    Safety standards EN60950-1
    IEC60950-1
    CNS14336-1
    Electromagnetic Compatibility (EMC) standards EN55032 Class A
    EN61000-3-2, EN61000-3-3
    EN55024
    EN301489-1, EN301489-3, EN301489-17
    EN62311
    EN50364
    CNS13438 Class A
    Identification of plastic components All plastic components that weigh more than 25 g are identified in accordance with ISO 11469 standards.
    Laser standards EN60825-1
    IEC60825-1
    Wireless LAN standards EN300328
    EN300330
    Radio Certificate (NCC)
  • Software and solutions
    Standard @Remote Embedded
    Web Image Monitor
    Device SDK
    Optional Device Manager NX
    InfoPrint Manager
    TotalFlow BatchBuilder
    TotalFlow Prep
    TotalFlow Production Manager
    TotalFlow Supervisor
    Ricoh ProcessDirector
    FusionPro VDP Creator
    FusionPro Expression
    OL PlanetPress Connect
    PrintShop Mail
    EFI Digital StoreFront
    EFI Graphic Arts Premium Edition
    EFI Fiery Central
    EFI JobFlow
    EFI Impose & Compose
  • Security features
    Encryption Encryption—print
    Authentication Simple network security setting
    DHCP option 60 and 77
    Other security features Security features are provided by the Ricoh GWNX controller. The Fiery E-46A and Fiery E-86A controller security is based on the EFI Fiery security policy compliant with the EFI Fiery System FS350 Pro.
  • Print features
    Print speed colour 85 ppm
    Print speed black and white 85 ppm
    Printing process 4-drum dry electrostatic transfer system with internal transfer belt
    Printing technology Vertical-cavity surface-emitting laser (VCSEL)
    Fusing Oil-less belt-fusing method
    Toner development PXP-EQ chemical toner, polymerisation
    Print resolution 2,400 x 4,800 dpi—VCSEL
    Page description languages (PDLs) Standard
    PCL 5c, PCL 6 (XL), PDF

    Optional
    Adobe PostScript 3
    Printer drivers

    Standard
    PCL 5c, PCL 6, RPCS

    Optional
    PostScript 3

    Printer driver resolution

    PCL 5c
    300 x 300 dpi—1-bit
    600 x 600 dpi—1-, 2-, and 4-bit; default

    Note:Supports font cache for high speed printing.

    PCL 6
    600 x 600 dpi—1-, 2-, and 4-bit; default
    1,200 x 1,200 dpi—1- and 2-bit

    Note:Supports font cache for high speed printing.

    PostScript 3
    600 x 600 dpi—1-, 2-, and 4-bit
    1,200 x 1,200 dpi—1- and 2-bit

    Note:TrueType and Type 1 fonts supported.

    RPCS
    600 x 600 dpi—1-, 2-, and 4-bit
    1,200 x 1,200 dpi—1- and 2-bit

    Note:Supports font cache for high speed printing.

    Duplex printing Standard
    Envelope printing Supported—with optional LCT RT5110 and vacuum-feed LCT RT5120
    Fonts

    PCL 5c, PCL 6
    136 Roman fonts, 13 International fonts

    PDF
    136 Roman fonts

    Maximum printable area 320 x 480 mm
    323 x 1,252 mm—with optional banner sheet tray
    Fiery controller
    Fiery colour controller E-46A or Fiery colour controller E-86A—optional
    Printer drivers
    Fiery E-46A
    PCL 5c, PCL 6, PostScript 3—CPSI v3020 and APPE v4.4

    Fiery E-86A
    PostScript 3—CPSI v3020 and APPE v4.4

    Printer driver fonts
    136 fonts and 2MM—PostScript 3
    80 fonts—PCL 5c and PCL 6

    Fiery menu via operation panel
    Supported

    Print resolution
    1,200 dpi, 2-bit
    600 dpi with PCL 5c

    Supported file formats
    PS, PDF, EPS, TIFF, PDF/VT, PPML, VPS, PCL—Fiery E-46A
    PS, PDF, EPS, TIFF, PDF/VT, PPML, VPS—Fiery E-86A

    Variable Data Printing (VDP)
    PPML v3, Fiery Free Form v1 and v2.1, PDF/VT-1 and PDF/VT-2
    TotalFlow TotalFlow Print Server R-62A—optional
  • Connectivity
    Interfaces - standard 10Base-T/100Base-Tx (Ethernet)
    1000Base-T (Gigabit Ethernet)
    SD slot x 3—1 on the controller board, 2 on the operation panel
    USB 2.0 Type A x 6—2 at rear of machine, 4 on the operation panel
    USB 2.0 Type Mini-B x 1—on the operation panel
    Network protocols - standard TCP/IP (IPv4, IPv6)
    MIB support Standard
    MIB-II (RFC1213)
    Host Resources (RFC1514)
    Printer MIB (RFC1759)
    Printer Port Monitor MIB

    Private
    Ricoh original MIB
  • Media Handling
    Standard input capacity (sheets) 2,500
    Maximum input capacity (sheets) 16,200
    Maximum output capacity (sheets) 13,000
    Paper input configuration - standard 1,000-sheet x 2 paper input tray, 500-sheet paper input tray, duplex unit
    Paper input configuration - optional 1,000-sheet A3 tray Type TK5010, 4,000-sheet LCT RT5110, 500-sheet multi-bypass tray BY5020, Multi-bypass attachment kit for vacuum feed LCT Type S9, 4,400-sheet vacuum-feed LCT RT5120, 500-sheet multi-bypass banner sheet tray Type S9, 730-sheet vacuum-feed banner sheet tray Type S9, Bridge unit BU5010,BDT VX 370-1280 banner sheet feeder, Plockmatic LCT3500
    Paper output configuration - optional Buffer pass unit Type S9, Decurler unit DU5060, Perfect Binder GB5010, 2-tray cover interposer CI5030, Multi-folding unit FD5020, Ring Binder RB5020, High-capacity stacker SK5040, 2,500-sheet booklet finisher SR5060, Booklet trimmer TR5040, 3,000-sheet finisher SR5050, Punch units PU5020, 3,500-sheet booklet finisher SR5120, 4,500-sheet finisher SR5110, Punch unit PU5030, Trimmer unit TR5050 for booklet finisher SR5120, Cover interposer CI5040
    Paper output configuration - 3rd Party Plockmatic HCI3500 high-capacity interposer, Plockmatic PBM 350 booklet maker, Plockmatic PBM 500 booklet maker, Plockmatic MPS1260 multi-purpose stacker, Plockmatic PBM 5035S long sheet stitcher, Plockmatic PBM 5035 long sheet stapler, Plockmatic SBT Square Back Trimmer, GBC StreamPunch Ultra
    Supported media

    Standard paper input tray 1
    Plain paper, recycled paper, pre-printed, letterhead, pre-punched

    Standard paper input tray 2
    Plain paper, recycled paper, pre-printed, letterhead, pre-punched, tab stock¹

    LCT RT5110 trays 3 and 5
    Plain paper, recycled paper, pre-printed, letterhead, pre-punched, tab stock², glossy/matte paper, OHP transparency, translucent paper, envelope, textured paper

    LCT RT5110 tray 4
    Plain paper, recycled paper, pre-printed, letterhead, pre-punched, tab stock², glossy/matte paper, OHP transparency, translucent paper, envelope, label paper, textured paper

    Vacuum-feed LCT RT5120
    Plain paper, recycled paper, pre-printed, letterhead, pre-punched, tab stock², glossy/matte paper, OHP transparency, translucent paper, envelope, textured paper

    Multi-bypass tray BY5020
    Plain paper, recycled paper, pre-printed, letterhead, pre-punched, tab stock², translucent paper

    Plockmatic LCT3500
    Plain paper, index paper, coated paper, recycled paper

    ¹—Tab sheet holder option is needed when printing tab stock
    ²—Tab fence is needed when printing tab stock

    Maximum paper size 13" x 19.2"
    Media weight (g/m2) 52.3–360
  • Supply yields
    Supply yields 45,000 sheets per 1,482 g bottle of black toner 45,000 sheets per 1,482 g bottle of cyan toner 45,000 sheets per 1,482 g bottle of magenta toner 45,000 sheets per 1,482 g bottle of yellow toner Note:All CMYK toner yields are measured with the A4/8.75% coverage chart, based on 50 pages per job and 80% duplex printing. 136,000 sheets per waste toner bottle Note:Based on A4/70% colour rate, 35% colour coverage, 6% black and white. 5,000 staples per Type M cartridge for finishers SR5050 and SR5060—normal staple 5,000 staples per Type U cartridge for finisher SR5060—saddle stitch staple 5,000 staples per Type M staple cartridgerefill for finishers SR5050 and SR5060—normal staple 5,000 staples per Type T staple cartridge refill for finisher SR5060—saddle stitch staple 75 sets per ring cartridge
  • Reliability
    Max monthly volume 240,000 prints
    Machine life 14,400,000 prints or 5 years, whichever comes first
    Duty cycle 650,000 prints per month
    Colour ratio 80%
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 1,320 x 910 x 1,218 mm
    Physical dimensions (WxDxH)—other 865 x 730 x 1,000 mm—4,000-sheet LCT RT5110
    1,054 x 730 x 1,000 mm—4,400-sheet vacuum-feed LCT RT5120
    330 x 730 x 1,000 mm—Bridge unit BU5010
    690 x 561 x 210 mm—500-sheet multi-bypass tray BY5020
    495 x 530 x 175 mm—1,000-sheet A3 tray Type TK5010
    1,290 x 730 x 1,000 mm—730-sheet vacuum-feed banner sheet tray Type S9
    1,090 x 561 x 210 mm—500-sheet multi-bypass banner sheet tray Type S9, when attached to multi-bypass tray BY5020
    1,688 x 1,286 x 950 mm—BDT VX 370-1280 banner sheet feeder
    730 x 1,220 x 1,090 mm—Plockmatic LCT3500
    330 x 730 x 1,010 mm—Buffer pass unit Type S9
    55 x 485 x 190 mm—Decurler unit DU5060
    996 x 730 x 1,126 mm—3,000-sheet finisher SR5050, with all extendable trays closed
    996 x 730 x 1,126 mm—2,500-sheet booklet finisher SR5060, with all extendable trays closed
    1,115 x 591 x 555 mm—Booklet trimmer TR5040
    1,113 x 730 x 1,490 mm—4,500-sheet finisher SR5110
    1,113 x 730 x 1,490 mm—3,500-sheet booklet finisher SR5120
    1,115 x 591 x 555 mm—Trimmer unit TR5050
    740 x 730 x 1,290 mm—Cover interposer CI5040
    870 x 730 x 1,010 mm—Ring Binder RB5020
    540 x 730 x 1,290 mm—2-tray cover interposer CI5030
    470 x 730 x 1,000 mm—Multi-folding unit FD5020
    1,090 x 791 x 1,387 mm—Perfect Binder GB5010
    900 x 730 x 1,010 mm—High-capacity stacker SK5040
    1,200 x 700 x 1,100 mm—Plockmatic high-capacity interposer HCI3500
    900 x 680 x 1,060 mm—Plockmatic multi-purpose stacker MPS1260
    1,420 x 700 x 970 mm—Plockmatic PBM 5035S/PBM 5035, including stacker
    265 x 253 x 136 mm—RPIP interface box Type S3
    Weight—mainframe 560 kg or less
    Weight—other 185 kg or less—4,000-sheet LCT RT5110
    230 kg or less—4,400-sheet vacuum-feed LCT RT5120
    40 kg or less—Bridge unit BU5010
    20 kg or less—500-sheet multi-bypass tray BY5020
    10 kg or less—1,000-sheet A3 tray Type TK5010
    7 kg or less—730-sheet vacuum-feed banner sheet tray Type S9
    9.5 kg or less—Multi-bypass banner sheet tray Type S9
    443 kg—BDT VX 370-1280 banner sheet feeder
    250 kg—Plockmatic LCT3500
    90 kg or less—Buffer pass unit Type S9
    5 kg or less—Decurler unit DU5060
    112 kg or less—3,000-sheet finisher SR5050
    112 kg or less—2,500-sheet booklet finisher SR5060
    75 kg or less—Booklet trimmer TR5040
    135 kg or less—4,500-sheet finisher SR5110
    160 kg or less—3,500-sheet booklet finisher SR5120
    75 kg—Trimmer unit TR5050
    50 kg—Cover interposer CI5040
    140 kg or less—Ring Binder RB5020
    45 kg or less—2-tray cover interposer CI5030
    92 kg or less—Multi-folding unit FD5020
    350 kg or less—Perfect Binder GB5010
    120 kg or less—High-capacity stacker SK5040
    15 kg or less—High-capacity stacker SK5040 roll-away cart
    250 kg—Plockmatic high-capacity interposer HCI3500
    65 kg—Plockmatic multi-purpose stacker MPS1260 lift unit
    5 kg—Plockmatic multi-purpose stacker MPS1260 docking unit
    0.55 kg or less—RPIP interface box Type S3
    Minimum space requirements

    1,000 mm—front
    1,000 mm—left
    1,000 mm—right
    800 mm—rear

    Note:PM parts maintenance tasks require additional rear clearance.

  • Configuration
    Functions Print
    Colour Yes
    Printer controller - standard GWNX
    Printer controller - optional EFI Fiery colour controller E-46A EFI Fiery colour controller E-86A Ricoh TotalFlow Print Server R-62A
    HDD 640 GB (320 GB x 2)
    CPU 1.91 GHz
    Memory - standard 4 GB
    Operation panel 17-inch touch panel
  • Environmental features
    Power source 220–240 V, 16 A, 50/60 Hz
    Power consumption 4,800 W or less—maximum power
    35 W or less—Energy Saver Mode (Sleep Mode)
    Power consumption—options 1,000 W or less—4,400-sheet Vacuum-Feed LCIT RT5150
    200 W or less—Buffer Pass Unit Type S9
    60 W or less—Multi-Folding Unit FD5030
    150 W or less—Finisher SR5110
    150 W or less—Booklet Finisher SR5120
    250 W or less, maximum—Trimmer Unit TR5050
    75 W or less, average—Trimmer Unit TR5050
    110 W excluding peak consumption—Cover Interposer CI5040
    Warm-up time 300 seconds or less
    Note:Based on 23C˚, rated voltage, and full options.
    Sound power level

    Mainframe
    58.5 dB or less—standby
    78.5 dB or less—operating

    System
    61 dB or less—standby, 85 ppm
    64 dB or less—standby, 95 ppm
    81.5 dB or less—operating

    Reduction of environmentally sensitive materials RoHS
    Less than 0.1 wt%—Lead, PVC, Hexavalent chromium, Cadmium, PBB/PBDE, DEHP, DBP, BBP, DIBP
    Energy saving standards Energy Star 3.2—with OneDFE controller
    Safety standards EN60950-1
    IEC60950-1
    KC 62368-1
    CNS 15998-1
    Electromagnetic Compatibility (EMC) standards EN55032 Class A
    EN61000-3-2
    EN61000-3-3
    EN55035
    EN62311
    KS C 9832
    KS C 9835
    KS C 9610-4-2
    KS C 9610-4-3
    CNS15936 Class A
    Identification of plastic components All plastic components that weigh more than 100 g are identified in accordance with ISO 11469 standards.
    Laser standards EN60825-1
    IEC60825-1
  • Software and solutions
    Standard @Remote
    TotalFlow Adviser
    Optional InfoPrint Manager
    Ricoh ProcessDirector
    TotalFlow Prep
    TotalFlow Production Manager
    TotalFlow BatchBuilder
    RICOH Supervisor
    TotalFlow Producer
    FusionPro VDP Creator
    FusionPro Expression
    Ricoh Auto Color Adjuster
    OL PlanetPress Connect
    Fiery Workflow Suite
  • Security features
    Other security features The OneDFE controller security is based on the EFI Fiery security policy that is compliant with the FS500 Pro system. Contact your local sales company for more information.
  • Print features
    Print speed colour 85 ppm—A4 LEF
    49 ppm—A3 SEF

    With optional Productivity Upgrade Unit Type S14
    95 ppm—A4 LEF
    53 ppm—A3 SEF
    Print speed black and white 85 ppm—A4 LEF
    49 ppm—A3 SEF

    With optional Productivity Upgrade Unit Type S14
    95 ppm—A4 LEF
    53 ppm—A3 SEF
    Printing process 4-drum or 5-drum dry electrostatic transfer system with internal transfer belt
    Printing technology Vertical-cavity surface-emitting laser (VCSEL)
    Fusing Oil-less belt-fusing method
    Toner development PXP-EQ chemical toner, polymerisation
    Print resolution 2,400 x 4,800 dpi
    Note:Engine print resolution is 1,200 x 4,800 dpi.
    Duplex printing Standard
    Envelope printing Supported—with optional Vacuum-Feed LCIT RT5150
    Maximum printable area 320 x 480 mm
    323 x 1,252 mm—with optional banner sheet tray
    Optional printer controller Color Controller N-50A and Color Controller N-70A

    System
    Fiery FS500 Pro

    Base operating system
    Windows 10 IoT Enterprise 2019 LTSC

    CPU
    Intel i5-8500—N-50A
    Intel Xeon 4214 (Silver)—N-70A

    HDD
    256 GB SSD SATA for OS; 1 TB HD SATA for data—N-50A
    480 GB SSD SATA for OS; 2 TB HD x 2 SATA for data—N-70A

    Memory (RAM)
    8 GB—N-50A
    32 GB—N-70A

    Interfaces
    Gigabit cross cable
    Ricoh data transfer unit cable
  • Connectivity
    Interfaces - standard 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet)—for TotalFlow Advisor connection 2.5GBase-T—for Fiery controller connection SD slot x 2— for maintenance only USB 3.0 x 4, USB 2.0 x 2
    Interfaces - optional With Color Controller N-50A 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet) USB 2.0 x 4—rear USB 3.0 x 5—2 ports on the rear, 3 ports on the Fiery Quick Touch operation panel With Color Controller N-70A 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet) USB 3.0 x 7—rear USB 3.0 x 4 ports, x3 ports on the Fiery Quick Touch operation panel
    Network protocols - standard TCP/IP (IPv4, IPv6)
    Network protocols - optional With Color Controller N-50A/N-70A Windows—TCP/IP Mac—TCP/IP, EtherTalk (for font download), Bonjour
  • Media Handling
    Standard input capacity (sheets) 2,500
    Maximum input capacity (sheets) 16,200
    Maximum output capacity (sheets) 13,000
    Paper input configuration - standard 1,000-sheet x 2 paper input tray 1, 500-sheet paper input tray 2, 500-sheet bypass tray, duplex unit
    Paper input configuration - optional 1,000-sheet A3/11"x 17" Tray Unit TK5010, 4,400-sheet Vacuum-Feed LCIT RT5150, Bridge Unit BU5010, 500-sheet Multi-Bypass Tray BY5020, 730-sheet Vacuum-Feed Banner Sheet Tray Type S9, 500-sheet Extension Vacuum-Feed Banner Sheet Tray Type S14, 500-sheet Multi-Bypass Banner Sheet Tray Type S9, 3,500-sheet Plockmatic LCT3500, BDT VX 370-1280 Feeder
    Paper output configuration - optional Buffer Pass Unit Type S9, Multi-Folding Unit FD5030, High-Capacity Stacker SK5040, 3,500-sheet Booklet Finisher SR5120, 4,500-sheet Finisher SR5110, Punch Unit PU5030, Trimmer Unit TR5050 for Booklet Finisher SR5120, 400-sheet Cover Interposer CI5040
    Paper output configuration - 3rd Party GBC e-Wire, GBC StreamPunch Plus, Plockmatic HCI3500 High-Capacity Interposer,Plockmatic CT XL, PlockmaticPBM350e, Plockmatic MPS1260 Multi-Purpose Stacker, Plockmatic PBM5035S long sheet stitcher, Plockmatic 5035 long sheet stapler,Plockmatic SBT (Square Back Trimmer),Plockmatic RCT v.3.0
    Supported media

    Standard paper input tray 1
    Plain, Recycled, Prepunched Paper, Textured Paper

    Standard paper input tray 2
    Plain, Recycled, Prepunched Paper, Transparency, Tab Stock, Translucent Paper, Textured Paper

    Bypass tray
    Plain, Recycled, Prepunched Paper, Transparency, Tab Stock, Translucent Paper, Envelope

    Note:High Gloss, Coated: Glossy, Coated: Matte, Textured Paper, and Synthetic Paper can be fed but quality is not guaranteed.

    OptionalA3/11"x 17" Tray Unit
    Plain, Recycled, Prepunched Paper, Textured Paper

    Optional Vacuum-Feed LCIT RT5150
    Plain, Recycled, Prepunched Paper, Transparency, Tab Stock, Translucent Paper, Label Paper, Coated: High Gloss, Coated: Glossy, Coated: Matte, Envelope, Textured Paper, Tab Stock: Glossy, Tab Stock: Matte, Tab Stock: High Gloss, Envelope: Glossy, Envelope Matte, Envelope: High Gloss, Carbonless Paper

    Note:Magnetic Paper, Metallic/Pearl Paper, Clear File Folder, and Synthetic Paper can be fed but quality is not guaranteed.

    Optional banner sheet tray
    Plain, Recycled, Prepunched Paper, Coated: High Gloss, Coated: Glossy, Coated: Matte, Textured Paper, Carbonless Paper

    Note:Magnetic Paper, Label Paper, Transparency, Metallic/Pearl Paper, Clear File Folder, and Synthetic Paper can be fed but quality is not guaranteed.

    Maximum paper size 330.2 x 1,260 mm
    Media weight (g/m2) 40–470
  • Supply yields
    Supply yields

    67,000 sheets—black
    67,000 sheets—cyan
    67,000 sheets—magenta
    67,000 sheets—yellow
    19,000 sheets—white
    29,200 sheets—neon yellow
    29,200 sheets—neon pink
    21,500 sheets—invisible red
    22,500 sheets—gold
    22,500 sheets—silver

    Note:CMYK and gold toner yields are measured with the A4/8.75% coverage chart with 50 pages per job. White neon yellow, neon pink, invisible red, and silver toner yields are measured with the A4/15% coverage chart with 50 pages per job.

    136,000 sheets per waste toner bottle

    Note:Waste toner bottle yield based on A4/8.75% coverage chart with 50 pages per job, 80% colour ratio.

    5,000 staples per Type X cartridge for Finisher SR5110 and Booklet Finisher SR5120—side staple
    5,000 staples per Type U cartridge for Booklet Finisher SR5120—saddle stitch staple
    5,000 staples per Type X refill cartridge for Finisher SR5110 and Booklet Finisher SR5120—side staple
    5,000 staples per Type T refill cartridge for Booklet Finisher SR5120—saddle stitch staple

  • Reliability
    Max monthly volume 240,000 prints
    Machine life 14,400,000 prints or 5 years, whichever comes first
    Duty cycle 1,500,000 prints—85 ppm; 1,700,000 prints—95 ppm
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 1,320 x 910 x 1,218 mm
    Physical dimensions (WxDxH)—other 1,320 x 910 x 1,816 mm—mainframe with Attention Light
    495 x 530 x 175 mm—A3/11"x 17" Tray Unit TK5010 (internal)
    1,054 x 730 x 1,000 mm—Vacuum-Feed LCIT RT5150
    1,290 x 730 x 1,000 mm—Vacuum-Feed LCIT RT5150 with Vacuum-Feed Banner Sheet Tray Type S9 attached
    1,519 x 730 x 1,000 mm—Vacuum-Feed LCIT RT5150 with Extension Vacuum-Feed Banner Sheet Tray Type S14 attached
    330 x 730 x 1,000 mm—Bridge Unit BU5010
    690 x 561 x 210 mm—Multi-Bypass Tray BY5020
    1,290 x 730 x 1,000 mm—Vacuum-Feed Banner Sheet Tray Type S9
    1,290 x 730 x 1,302 mm—Vacuum-Feed Banner Sheet Tray Type S9, with cover open
    1,519 x 730 x 1,000 mm—Extension Vacuum-Feed Banner Sheet Tray Type S14, when attached to Vacuum-Feed LCIT RT5150
    1,090 x 561 x 210 mm—Multi-Bypass Banner Sheet Tray Type S9, when attached to Multi-Bypass Tray BY5020
    730 x 1,220 x 1,090 mm—Plockmatic LCT3500 2.0
    1,688 x 1,286 x 950 mm—BDT VX 370-1280 Feeder
    330 x 730 x 1,010 mm—Buffer Pass Unit Type S9
    1,113 x 730 x 1,490 mm—Finisher SR5110
    1,334 x 730 x 1,622 mm—Finisher SR5110 with SR5000 Series Output Tray for Banner Sheet Type S6
    1,876 x 730 x 1,617 mm—Finisher SR5110 with Extension Output Banner Sheet Tray Type S14 (installed on the upper tray)
    1,926 x 730 x 1,617 mm—Finisher SR5110 with Extension Output Banner Sheet Tray Type S14 (installed on the lower tray)
    1,113 x 730 x 1,490 mm—Booklet Finisher SR5120
    1,334 x 730 x 1,622 mm—Booklet Finisher SR5120 with SR5000 Series Output Tray for Banner Sheet Type S6
    1,876 x 730 x 1,617 mm—Booklet Finisher SR5120 with Extension Output Banner Sheet Tray Type S14 (installed on the upper tray)
    1,926 x 730 x 1,617 mm—Booklet Finisher SR5120 with Extension Output Banner Sheet Tray Type S14 (installed on the lower tray)
    1,115 x 591 x 555 mm—Trimmer Unit TR5050
    740 x 730 x 1,350 mm—Cover Interposer CI5040
    209 x 730 x 1,000 mm—Multi-Folding Unit FD5030
    900 x 730 x 1,010 mm—High-Capacity Stacker SK5040
    1,200 x 700 x 1,100 mm—Plockmatic High-Capacity Stacker HCI3500
    900 x 680 x 1,060 mm—Plockmatic Multi-Purpose Stacker MPS1260
    1,420 x 700 x 970 mm—Plockmatic PBM 5035S/PBM 5035, including stacker
    Weight—mainframe 590 kg or less—4-station; 610 kg or less—5-station
    Weight—other 10 kg or less—A3/11"x 17" Tray Unit TK5010
    230 kg or less—Vacuum-Feed LCIT RT5150
    40 kg or less—Bridge Unit BU5010
    20 kg or less—Multi-Bypass Tray BY5020
    9 kg or less—Vacuum-Feed Banner Sheet Tray Type S9
    23 kg or less—Extension Vacuum-Feed Banner Sheet Tray Type S14
    9.5 kg or less—Multi-Bypass Banner Sheet Tray Type S9
    250 kg—Plockmatic LCT3500 2.0
    443 kg—BDT VX 370-1280 Feeder
    90 kg or less—Buffer Pass Unit Type S9
    135 kg—Finisher SR5110
    160 kg—Booklet Finisher SR5120
    75 kg—Trimmer Unit TR5050
    60 kg—Cover Interposer CI5040
    45 kg or less—Multi-Folding Unit FD5030
    131 kg or less—High-Capacity Stacker SK5040
    135 kg or less—High-Capacity Stacker SK5040 with roll-away cart
    250 kg—Plockmatic High-Capacity Stacker HCI3500
    65 kg—Plockmatic Multi-Purpose Stacker MPS1260 lift unit
    5 kg—Plockmatic Multi-Purpose Stacker MPS1260 docking unit
    Minimum space requirements 1,000 mm—front
    1,000 mm—left
    1,000 mm—right
    800 mm—rear
  • Configuration
    Functions Print
    Colour Yes
    Printer controller - standard RICOH GC OS
    Printer controller - optional Color Controller N-50A
    Color Controller N-70A
    Operation panel 21.5" Full HD touchscreen
  • Environmental features
    Power source 220–240 V, 50/60 Hz, less than 60 A
    Power consumption 9,000 W or less—maximum power
    4 W or less—Energy Saver Mode (Sleep Mode)
    Power consumption—options 350 W—Fiery E-46 controller
    600 W—Fiery E-86 controller
    1,000 W or less—4,400-sheet vacuum feed LCT RT5120
    150 W or less—3,000-sheet finisher SR5050
    150 W or less—2,500-sheet booklet finisher SR5060
    250 W or less, maximum—Booklet trimmer TR5040
    75 W or less, average—Booklet trimmer TR5040
    150 W or less—4,500-sheet finisher SR5110
    150 W or less—3,500-sheet booklet finisher SR5120
    250 W or less, maximum—Trimmer unit TR5050
    75 W or less, average—Trimmer unit TR5050
    95 W excluding peak consumption—Cover interposer CI5040
    400 W or less—Ring Binder RB5020
    623 W or less—Perfect Binder GB5010
    240 W or less—Multi-purpose folding unit FD5020
    132 W or less—High-capacity stacker SK5040
    Warm-up time 540 seconds or less—mainframe
    380 seconds or less—Perfect Binder GB5010
    Sound power level Mainframe
    67.5 dB—standby
    80 dB—operating
    Emission levels

    Colour mode
    Less than 0.01 mg/h—benzene
    0.7 mg/h or less—dust
    9.1 mg/h or less—ozone
    0.13 mg/h or less—styrene

    Black and white mode
    Less than 0.01 mg/h—benzene
    0 mg/h or less—dust
    3.1 mg/h—ozone
    0.08 mg/h or less—styrene

    Total Volatile Organic Compounds (TVOC) 0.8 mg/h—ready mode
    3.0 mg/h—operating mode
    Reduction of environmentally sensitive materials RoHS
    100% lead-free solder used in PCBs—lead
    0%—PVC
    100% chrome-free steel plates—hexavalent chromium
    0%—cadmium
    0%—PBB/PBDE
    Energy saving standards

    Energy Star v2.0—with EFI Fiery controller

    Safety standards EN60950-1
    IEC60950-1
    Electromagnetic Compatibility (EMC) standards EN55032 Class A
    EN61000-3-2, EN61000-3-3
    EN55024
    EN301489-1, EN301489-3, EN301489-17
    EN62311
    EN50364
    Identification of plastic components All plastic components that weigh more than 25 g are identified in accordance with ISO 11469 standards.
    Laser standards EN60825-1
    IEC60825-1
    Wireless LAN standards EN300328
    EN300330
  • Software and solutions
    Standard @Remote Embedded Web Image Monitor Device SDK
    Optional Device Manager NX InfoPrint Manager TotalFlow BatchBuilder TotalFlow Prep TotalFlow Production Manager TotalFlow Supervisor Ricoh ProcessDirector FusionPro VDP Creator FusionPro Expression OL PlanetPress Connect PrintShop Mail EFI Digital StoreFront EFI Fiery Central EFI JobFlow EFI Impose & Compose
  • Supported operating environments
    Other supported environments

    Fiery

    Windows operating system
    These Windows versions (with latest service packs) are supported for printer drivers and Fiery applications:
    Windows Vista—Home Basic, Home Premium, Ultimate, Business, Enterprise
    Windows 7—Home Premium, Professional, Ultimate
    Windows 8.1—Windows 8.1, Pro, Enterprise
    Windows 10—Home, Pro, Enterprise, Education
    Windows Server 2008—Standard, Enterprise
    Windows Server 2008 R2, 64-bit—Foundation Standard, Enterprise
    Windows Server 2012, 64-bit—Foundation, Essentials, Standard
    Windows Server 2012 R2,64-bit—Foundation, Essentials, Standard
    Windows Server 2016,64-bit—Standard, Essentials, MultiPoint, Premium Server

    Macintosh operating system
    These Mac OS versions are supported for printer drivers:
    Mac OS v10.6, v10.7, v10.8, v10.9, v10.10, v10.11, v10.12

    HDD—for printing and utilities except Command WorkStation
    Windows—1 GB free space (2 GB recommended)
    Mac OS X—500 MB free space (1 GB recommended)

    Memory (RAM)—for printing and utilities except Command WorkStation
    Windows—500 MB (2 GB recommended)
    Mac OS X—500 MB (1 GB recommended)

    Networking protocols
    Windows—TCP/IP
    Mac OS X—TCP/IP, Bonjour

    WebTools
    Windows—Internet Explorer 11 or later, Firefox 48 or later, Chrome 52 or later, Microsoft Edge for client computers running Windows 10
    Mac OS—Safari 8 or later, Firefox 48 or later, Chrome 52 or later

    Note:Microsoft releases frequent updates to Internet Explorer. Because support cannot be guaranteed for all versions, use the versions specified for best results.

    Command WorkStation

    Windows:
    1.0 GHz or greater Pentium 4 processor
    1 GB RAM or more
    16 GB HDD space free
    A monitor that supports 16-bit colour at a minimum resolution of 1,024 x 768 pixels
    TCP/IP networking protocol installed

    Mac OS X:
    Safari 8 or later, Firefox 48 or later, Chrome 52 or later
    4 GB RAM or more
    7 GB HDD space free

    Fiery Job Master (Impose and Compose) on Command WorkStation

    In addition to requirements for Command WorkStation:
    Licence activation for every client workstation
    Acrobat/PitStop software

    Supported languages With Fiery controller
    Print, PCL 6, PostScript 3
    English, German, French, Italian, Spanish, Dutch, Czech, Polish, Russian, Turkish, Simplified Chinese, Korean, Brazilian Portuguese
  • Security features
    Encryption Encryption—print
    Authentication Simple network security setting
    DHCP option 60 and 77
    Other security features Security features are based on the GWNX security policy, which is compliant with the latest Ricoh security specifications. The EFI Fiery E-46 and Fiery E‑86 controller security is based on the EFI Fiery security policy that is compliant with the Fiery FS350 system. Refer to your local sales company for more information.
  • Print features
    Print speed colour 115 ppm—A4 62 ppm—A3 57 ppm—SRA3, 12" x 18" 32 ppm—700 mm 16 ppm—1,260 mm
    Print speed black and white 115 ppm—A4 62 ppm—A3 57 ppm—SRA3, 12" x 18" 32 ppm—700 mm 16 ppm—1,260 mm
    First print time 24 seconds
    Productivity 100%—A3
    Printing process 4-drum dry electrostatic transfer system with internal transfer belt
    Printing technology Vertical-cavity surface-emitting laser (VCSEL)
    Fusing Oil-less belt-fusing method
    Toner development PXP-EQ chemical toner, polymerisation
    Print resolution 2,400 x 4,800 dpi
    Printer drivers PCL 6, PostScript 3—optional with Fiery
    Duplex printing Standard
    Envelope printing Supported—Tray 1, Tray 2, Vacuum-feed LCT RT5120, Multi-bypass tray BY5020
    Maximum printable area 326 x 1,255 mm—full bleed on 3 edges except leading edge 323 x 700 mm—image quality guaranteed Blank margin—uncoated media Leading edge: 7.0 +/- 0.5 mm1 4.0 +/- 0.5 mm2 2.5 +/- 0.5 mm3 Trailing edge: 7.0 +/- 0.5 mm1 4.0 +/- 0.5 mm2 2.5 +/- 0.5 mm3 Blank margin—coated media Leading edge: 7.0 +/- 0.5 mm1 4.0 +/- 0.5 mm2 3.5 +/- 0.5 mm3 Trailing edge: 7.0 +/- 0.5 mm1 4.0 +/- 0.5 mm2 3.5 +/- 0.5 mm3 1—Thick 1–4 2—Thick 5–7 3—Thick 8–9
    Fiery controller EFI Fiery colour controller E-46 and E-86—optional The print features are provided via the external EFI Fiery E-46 or Fiery E-86 controller. System version Fiery E-46 Fiery PS350 Pro Fiery E-86 Fiery PS350 Premium Configuration External Page Description Languages (PDLs) PCL 6, PostScript 3—CPSI v3020 and APPE v4.4 Print resolution 1,200 x 1,200 dpi, 2-bit Printer driver fonts 80 fonts—PCL 136 fonts + 2MM—PostScript 3 Fiery menu via operation panel Supported 2-character controller panel Supported—for technical service use Supported file formats PS, PDF, EPS, TIFF, PDF/VT, PPML, VPS, PCL—Fiery E-46 PS, PDF, EPS, TIFF, PDF/VT, PPML, VPS—Fiery E-86 Variable Data Printing (VDP) PPML v3 Fiery FreeForm v1 and 2.1 PDF/VT-1 and PDF/VT-2 Note:Creo VPS is available from EFI but not supported by Ricoh.
    TotalFlow TotalFlow Print Server R-62—optional
    Other print features Optional Auto Colour Diagnosis Unit and Image Quality Monitor
  • Connectivity
    Interfaces - standard 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet)—for Fiery controller connection SD slot x 3—2 ports on rear, 1 port on the operation panel USB host x 3—2 ports on rear, 1 port on the operation panel
    Interfaces - optional RPIP interface box Type S3 With Fiery controller 10Base-T/100Base-Tx (Ethernet) 1000Base-T (Gigabit Ethernet) USB 2.0 x 2—rear USB 3.0 x 5—3 ports in Fiery Quick Touch, 2 ports on the rear
    Network protocols - standard TCP/IP (IPv4, IPv6)
    Network protocols - optional With Fiery controller TCP/IP (IPv4, IPv6), SMB
  • Media Handling
    Standard input capacity (sheets) 4,400
    Maximum input capacity (sheets) 18,100
    Maximum output capacity (sheets) 13,000
    Paper input configuration - standard 2,200-sheet paper input tray x 2, duplex unit
    Paper input configuration - optional 4,400-sheet vacuum-feed LCT RT5120, Multi-bypass attachment kit for vacuum-feed LCT Type S9,500-sheet multi-bypass tray BY5020, 730-sheet vacuum-feed banner sheet tray Type S9, 500-sheet multi-bypass banner sheet tray Type S9, Bridge unit BU5010,BDT VX 370-1280 banner sheet feeder, Plockmatic LCT3500
    Paper output configuration - optional 3,000-sheet finisher SR5050, 2,500-sheet booklet finisher SR5060, 2 tray cover interposer CI5030, Booklet trimmer TR5040, Ring Binder RB5020, Perfect Binder GB5010, Multi-folding unit FD5020, High-capacity stacker SK5040, Punch unit PU5020,3,500-sheet booklet finisher SR5120, 4,500-sheet finisher SR5110, Punch unit PU5030, Trimmer unit TR5050 for booklet finisher SR5120, Cover interposer CI5040
    Paper output configuration - 3rd Party GBC StreamPunch Ultra, Plockmatic booklet maker PBM 350/PBM 500, Plockmatic high-capacity interposer HCI3500,Plockmatic multi-purpose stacker MPS1260,Plockmatic PBM 5035S long sheet stitcher, Plockmatic PBM 5035 long sheet stapler
    Supported media

    Standard paper input trays 1 and 2
    Plain paper, coated paper (glossy and matte), recycled paper, pre printed, letterhead, pre-punched, tab stock1, OHP transparency, translucent paper, envelope, textured paper, label paper, NCR paper

    Note:Metallic paper, synthetic paper, water resistant paper, and magnetic paper can be fed but support is not guaranteed.

    Vacuum-feed LCT RT5120

    Plain paper, coated paper (glossy and matte), recycled paper, pre printed, letterhead, pre-punched, tab stock1, OHP transparency, translucent paper, envelope, textured paper, label paper, NCR paper

    Note:Metallic paper, synthetic paper, water resistant paper, and magnetic paper can be fed but support is not guaranteed.

    Vacuum-feed banner sheet tray Type S9
    Plain paper, coated paper (glossy and matte), recycled paper, pre printed, letterhead, textured paper

    Note:Pre-punched, tab stock1, OHP transparency, translucent paper, metallic paper, synthetic paper, water resistant paper, magnetic paper, and label paper can be fed but support is not guaranteed.

    Multi-bypass tray BY5020
    Plain paper, recycled paper, pre-printed, letterhead, pre-punched, tab stock1, translucent paper, envelope

    Note:Coated, textured paper, and synthetic paper can be fed but support is not guaranteed.

    Duplex unit
    Plain paper, coated paper (glossy and matte), recycled paper, pre printed, letterhead, pre-punched, OHP transparency, textured paper, synthetic paper, metallic paper

    Plockmatic LCT3500
    Plain paper, index paper, coated paper, recycled paper

    ¹—Tab fence is needed when printing tab stock

    Maximum paper size 13" x 19.2"
    Media weight (g/m2) 52–470
    Limitless paper supply Supported
  • Supply yields
    Supply yields 59,800 sheets per 1,482g black toner bottle 60,500 sheets per 1,482 g cyan, magenta, and yellow bottle 220,000 sheets per waste toner bottle 5,000 staples per Type M cartridge for finisher SR5050 and SR5060—normal staple 5,000 staples per Type Ucartridge for finisher SR5060—saddle stitch staple 5,000 staples perType M refill cartridge for finisher SR5050 and SR5060—normal staple 5,000 staples per Type Trefill cartridge for finisher SR5060—saddle stitch staple 52 sets x 5 per 100-ring carton—260 booklets/carton 66 sets x 5 per 50-ring carton—330 booklets/carton Note:Toner yields measured with the A4/8.75% coverage chart with 150 pages per job.Waste toner bottle yield measured with A4/8.75% coverage chart with 150 pages per job and 80% colour ratio.
  • Reliability
    Average monthly volume 350,000 prints—A4
    200,000 prints—click
    Max monthly volume 1,000,000 prints
    Max volume statement 100,000–650,000 prints per month—recommended document volume
    Machine life 60,000,000 prints or 5 years, whichever comes first
    Duty cycle 1,750,000 prints
    Colour ratio 80%
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 2,520 x 990 x 1,500 mm
    Physical dimensions (WxDxH)—other 2,520 x 990 x 1,870 mm—mainframe with status pole
    1,054 x 730 x 1,000 mm—4,400-sheet vacuum-feed LCT RT5120
    1,290 x 730 x 1,000 mm—4,400-sheet vacuum-feed LCT RT5120 with banner sheet option attached
    330 x 730 x 1,000 mm—Bridge unit BU5010
    690 x 561 x 210 mm—500-sheet multi-bypass tray BY5020
    1,290 x 730 x 1,000 mm—730-sheet vacuum-feed banner sheet tray Type S9
    1,290 x 730 x 1,302 mm—730-sheet vacuum-feedbanner sheet tray Type S9, when cover is open
    1,090 x 561 x 210 mm—500-sheet multi-bypass banner sheet tray Type S9, when attached to multi-bypass tray BY5020
    1,688 x 1,286 x 950 mm—BDT VX 370-1280 banner sheet feeder
    730 x 1,220 x 1,090 mm—Plockmatic LCT3500
    996 x 730 x 1,126 mm—3,000-sheet finisher SR5050, with all extendable trays closed
    996 x 730 x 1,126 mm—2,500-sheet booklet finisher SR5060, with all extendable trays closed
    1,115 x 591 x 555 mm—Booklet trimmer TR5040
    1,113 x 730 x 1,490 mm—4,500-sheet finisher SR5110
    1,113 x 730 x 1,490 mm—3,500-sheet booklet finisher SR5120
    1,115 x 591 x 555 mm—Trimmer unit TR5050
    740 x 730 x 1,290 mm—Cover interposer CI5040
    870 x 730 x 1,010 mm—Ring Binder RB5020
    540 x 730 x 1,290 mm—2-tray cover interposer CI5030
    470 x 730 x 1,000 mm—Multi-folding unit FD5020
    1,090 x 791 x 1,387 mm—Perfect Binder GB5010
    1,114x 1,048 x 1,178 mm—High-capacity stacker SK5040
    1,200 x 700 x 1,100 mm—Plockmatic high-capacity stacker HCI3500
    900 x 680 x 1,060 mm—Plockmatic multi-purpose stacker MPS1260
    1,420 x 700 x 970 mm—Plockmatic PBM 5035S/PBM 5035, including stacker
    265 x 253 x 136 mm—RPIP interface box Type S3
    Weight—mainframe 1,076 kg or less
    Weight—other 230 kg or less—4,400-sheet vacuum-feed LCT RT5120
    40 kg or less—Bridge unit BU5010
    20 kg or less—500-sheet multi-bypass tray BY5020
    9 kg or less—730-sheet vacuum-feed banner sheet tray Type S9
    9.5 kg or less—Multi-bypass banner sheet tray Type S9
    443 kg—BDT VX 370-1280 banner sheet feeder
    250 kg—Plockmatic LCT3500
    112 kg or less—3,000-sheet finisher SR5050
    112 kg or less—2,500-sheet booklet finisher SR5060
    75 kg or less—Booklet trimmer TR5040
    135 kg or less—4,500-sheet finisher SR5110
    160 kg or less—3,500-sheet booklet finisher SR5120
    75 kg—Trimmer unit TR5050
    50 kg—Cover interposer CI5040
    140 kg or less—Ring Binder RB5020
    45 kg or less—2-tray cover interposer CI5030
    92 kg or less—Multi-folding unit FD5020
    350 kg or less—Perfect Binder GB5010
    131 kg or less—High-capacity stacker SK5040
    250 kg—Plockmatic high-capacity stacker HCI3500
    65 kg—Plockmatic multi-purpose stacker MPS1260 lift unit
    5 kg—Plockmatic multi-purpose stacker MPS1260 docking unit
    0.55 kg or less—RPIP interface box Type S3
    Minimum space requirements

    1,000 mm—front
    1,000 mm—left
    1,000 mm—right
    800 mm—rear

    Note:PM parts maintenance tasks require additional rear clearance.

  • Configuration
    Functions Print
    Colour Yes
    Printer controller - standard GWNX—embedded
    Printer controller - optional EFI Fiery colour controller E-46
    EFI Fiery colour controller E-86
    Ricoh TotalFlow Print Server R-62
    HDD 320 GB
    CPU 1.06 GHz
    Memory - standard 1 GB
    Operation panel 17-inch LCD touch screen operation panel
  • Environmental features
    Power source 220–240 V, 50/60 Hz
    Power consumption 9,000 W or less—maximum power
    Power consumption—options 1,000 W or less—Vacuum-Feed LCIT RT5150
    150 W or less—Finisher SR5110
    150 W or less—Booklet Finisher SR5120
    250 W or less, maximum—Trimmer Unit TR5050
    75 W or less, average—Trimmer Unit TR5050
    110 W excluding peak consumption—Cover Interposer CI5040
    Warm-up time 540 seconds or less—mainframe
    Sound power level Mainframe
    73.5 dB or less—standby
    81.5 dB or less—operating
    Reduction of environmentally sensitive materials RoHS
    Less than 0.1 wt%—Lead, PVC, Hexavalent chromium, Cadmium, PBB/PBDE, DEHP, DBP, BBP, DIBP
    Energy saving standards

    Energy Star 3.2—with OneDFE controller

    Safety standards EN60950-1
    IEC60950-1
    KC 62368-1
    CNS 15998-1
    Electromagnetic Compatibility (EMC) standards EN55032 Class A
    EN61000-3-2
    EN61000-3-3
    EN55035
    EN62311
    KS C 9832
    KS C 9835
    KS C 9610-4-2
    KS C 9610-4-3
    CNS15936 Class A
    Identification of plastic components All plastic components that weigh more than 100 g are identified in accordance with ISO 11469 standards.
    Laser standards EN60825-1
    IEC60825-1
  • Software and solutions
    Standard  @Remote
    TotalFlow Adviser
    Optional InfoPrint Manager
    Ricoh ProcessDirector
    TotalFlow Prep
    TotalFlow Production Manager
    TotalFlow BatchBuilder
    RICOH Supervisor
    TotalFlow Producer
    FusionPro VDP Creator
    FusionPro Expression
    Ricoh Auto Color Adjuster
    OL PlanetPress Connect
    Fiery Workflow Suite
  • Security features
    Other security features The OneDFE controller security is based on the EFI Fiery security policy that is compliant with the FS500 Pro system. Contact your local sales company for more information.
  • Print features
    Print speed colour 115 ppm—A4 62 ppm—A3With optional Productivity Upgrade Unit Type S15 135 ppm—A4 75 ppm—A3
    Print speed black and white 115 ppm—A4 62 ppm—A3With optional Productivity Upgrade Unit Type S15 135 ppm—A4 75 ppm—A3
    First print time 115 ppm—24 seconds; 135 ppm—22 seconds
    Printing process 4-drum dry electrostatic transfer system with internal transfer belt
    Printing technology Vertical-cavity surface-emitting laser (VCSEL)
    Fusing Oil-less belt-fusing method
    Toner development PXP-EQ chemical toner, polymerisation
    Print resolution 2,400 x 4,800 dpi Note:Engine print resolution is 1,200 x 4,800 dpi.
    Duplex printing Standard
    Envelope printing Supported
    Maximum printable area 326 x 1,255 mm
    Optional printer controller Color Controller N-50 and Color Controller N-70 System Fiery FS500 Pro Base operating system Windows 10 IoT Enterprise 2019 LTSC CPU Intel i5-8500—N-50 Intel Xeon 4214 (Silver)—N-70 HDD 256 GB SSD SATA for OS;1 TB HD SATA for data—N-50 480 GB SSD SATA for OS;2 TB HD x 2 SATA for data—N-70
    Memory (RAM)
    8 GB—N-50 32 GB—N-70 Interfaces Gigabit cross cable Ricoh data transfer unit cable
    Other print features Optional Auto Color Diagnosis Unit and Image Quality Monitor
  • Connectivity
    Interfaces - standard 10Base-T/100Base-Tx (Ethernet) 
    1000Base-T (Gigabit Ethernet)—for TotalFlow Advisor connection
    2.5GBase-T—for Fiery controller connection
    SD slot x 2— for maintenance only 
    USB 3.0 x 4, USB 2.0 x 2
    Interfaces - optional  With Color Controller N-50

    10Base-T/100Base-Tx (Ethernet) 
    1000Base-T (Gigabit Ethernet)
    USB 2.0 x 4—rear 
    USB 3.0 x 5—2 ports on the rear, 3 ports on the Fiery Quick Touch operation panel

     

    With Color Controller N-70
    10Base-T/100Base-Tx (Ethernet) 
    1000Base-T (Gigabit Ethernet)
    USB 3.0 x 7—rear USB 3.0 x 4 ports, x3 ports on the Fiery Quick Touch operation panel
    Network protocols - standard TCP/IP (IPv4, IPv6)
    Network protocols - optional With Color Controller N-50/N-70
    Windows—TCP/IP
    Mac—TCP/IP, EtherTalk, Bonjour 
  • Media Handling
    Standard input capacity (sheets) 4,400
    Maximum input capacity (sheets) 18,100
    Maximum output capacity (sheets) 13,000
    Paper input configuration - standard 2,200-sheet paper input tray x 2
    Paper input configuration - optional 4,400-sheet Vacuum-Feed LCIT RT5150, Bridge Unit BU5010, 500-sheet Multi-Bypass Tray BY5020, 730-sheet Vacuum-Feed Banner Sheet Tray Type S9, 500-sheet Extension Vacuum-Feed Banner Sheet Tray Type S14, 500-sheet Multi-Bypass Banner Sheet Tray Type S9, 3,500-sheet Plockmatic LCT3500
    Paper output configuration - optional Multi-Folding Unit FD5030, High-Capacity Stacker SK5040, 3,500-sheet Booklet Finisher SR5120, 4,500-sheet Finisher SR5110, Punch Unit PU5030, Trimmer Unit TR5050 for Booklet Finisher SR5120, 400-sheet Cover Interposer CI5040
    Paper output configuration - 3rd Party GBC e-Wire, GBC StreamPunch Plus, Plockmatic HCI3500 High-Capacity Interposer, Plockmatic CT XL, Plockmatic PBM350e, Plockmatic MPS1260 Multi-Purpose Stacker, Plockmatic PBM5035S long sheet stitcher, Plockmatic 5035 long sheet stapler, Plockmatic SBT (Square Back Trimmer), Plockmatic RCT v.3.0
    Supported media  

    Standard paper input trays 1 and 2
    Plain, Recycled, Prepunched Paper, Transparency, Tab Stock, Translucent Paper, Label Paper, Coated: High Gloss, Coated: Glossy, Coated: Matte, Envelope, Textured Paper, Tab Stock: Glossy, Tab Stock: Matte, Tab Stock: High Gloss, Envelope: Glossy, Envelope: Matte, Envelope: High Gloss, Carbonless Paper

    Note: Magnetic Paper, Metallic/Pearl Paper, Clear File Folder, and Synthetic Paper can be fed but quality is not guaranteed.

    Bypass tray
    Plain, Recycled, Prepunched Paper, Transparency, Tab Stock, Translucent Paper, Envelope

    Note: High Gloss, Coated: Glossy, Coated: Matte, Textured Paper, and Synthetic Paper can be fed but quality is not guaranteed.

    Optional Vacuum-Feed LCIT RT5150
    Plain, Recycled, Prepunched Paper, Transparency, Tab Stock, Translucent Paper, Label Paper, Coated: High Gloss, Coated: Glossy, Coated: Matte, Envelope, Textured Paper, Tab Stock: Glossy, Tab Stock: Matte, Tab Stock: High Gloss, Envelope: Glossy, Envelope Matte, Envelope: High Gloss, Carbonless Paper

    Note: Magnetic Paper, Metallic/Pearl Paper, Clear File Folder, and Synthetic Paper can be fed but quality is not guaranteed.

    Optional banner sheet tray
    Plain, Recycled, Prepunched Paper, Coated: High Gloss, Coated: Glossy, Coated: Matte, Textured Paper, Carbonless Paper

    Note: Transparency, Translucent Paper, Label Paper, Magnetic Paper, Metallic/Pearl Paper, and Synthetic Paper can be fed but quality is not guaranteed.

    Maximum paper size 13" x 19.2"
    Media weight (g/m2) 40–470
    Limitless paper supply  Supported
     
  • Supply yields
    Supply yields 69,000 sheets—black

    75,500 sheets—cyan
    73,200 sheets—magenta
    64,800 sheets—yellow

    230,000 sheets per waste toner bottle

    5,000 staples per Type X cartridge for Finisher SR5110 and Booklet Finisher SR5120—side staple
    5,000 staples per Type U cartridge for Booklet Finisher SR5120—saddle stitch staple
    5,000 staples per Type X refill cartridge for Finisher SR5110 and Booklet Finisher SR5120—side staple
    5,000 staples per Type T refill cartridge for Booklet Finisher SR5120—saddle stitch staple

    Note: Toner yields measured with the A4/8.75% coverage chart with 150 pages per job. Waste toner bottle yield measured with A4/8.75% coverage chart with 150 pages per job and 80% colour ratio.

  • Reliability
     Average monthly volume  115 ppm—251,000 prints (A4), 159,000 prints (click); 135 ppm—460,000 prints (A4), 304,000 prints (click)
     Max monthly volume  1,000,000 prints
     Machine life  60,000,000 prints or 5 years, whichever comes first
     Duty cycle  115 ppm—2,250,000 prints; 135 ppm—2,600,000 prints
     Colour ratio  80%
  • Configuration
     
    Functions Print
    Colour Yes
    Printer controller - standard RICOH GC OS
    Printer controller - optional Color Controller N-50 Color Controller N-70
    Operation panel 21.5" Full HD touchscreen
  • Physical dimensions
    Physical dimensions (WxDxH)—mainframe 2,520 x 990 x 1,500 mm
    Physical dimensions (WxDxH)—other 2,520 x 990 x 1,870 mm—mainframe with Attention Light
    1,054 x 730 x 1,000 mm—Vacuum-Feed LCIT RT5150
    1,290 x 730 x 1,000 mm—Vacuum-Feed LCIT RT5150 with Vacuum-Feed Banner Sheet Tray Type S9 attached
    1,519 x 730 x 1,000 mm—Vacuum-Feed LCIT RT5150 with Extension Vacuum-Feed Banner Sheet Tray Type S14 attached
    330 x 730 x 1,000 mm—Bridge Unit BU5010
    690 x 561 x 210 mm—Multi-Bypass Tray BY5020
    1,290 x 730 x 1,000 mm—Vacuum-Feed Banner Sheet Tray Type S9
    1,290 x 730 x 1,302 mm—Vacuum-Feed Banner Sheet Tray Type S9, with cover open
    1,519 x 730 x 1,000 mm—Extension Vacuum-Feed Banner Sheet Tray Type S14, when attached to Vacuum-Feed LCIT RT5150
    1,090 x 561 x 210 mm—Multi-Bypass Banner Sheet Tray Type S9, when attached to Multi-Bypass Tray BY5020
    730 x 1,220 x 1,090 mm—Plockmatic LCT3500 2.0
    1,113 x 730 x 1,490 mm—Finisher SR5110
    1,334 x 730 x 1,622 mm—Finisher SR5110 with SR5000 Series Output Tray for Banner Sheet Type S6
    1,876 x 730 x 1,617 mm—Finisher SR5110 with Extension Output Banner Sheet Tray Type S14  (installed on the upper tray)
    1,926 x 730 x 1,617 mm—Finisher SR5110 with Extension Output Banner Sheet Tray Type S14  (installed on the lower tray)
    1,113 x 730 x 1,490 mm—Booklet Finisher SR5120
    1,334 x 730 x 1,622 mm—Booklet Finisher SR5120 with SR5000 Series Output Tray for Banner Sheet Type S6
    1,876 x 730 x 1,617 mm—Booklet Finisher SR5120 with Extension Output Banner Sheet Tray Type S14  (installed on the upper tray)
    1,926 x 730 x 1,617 mm—Booklet Finisher SR5120 with Extension Output Banner Sheet Tray Type S14  (installed on the lower tray)
    1,115 x 591 x 555 mm—Trimmer Unit TR5050
    740 x 730 x 1,350 mm—Cover Interposer CI5040
    209 x 730 x 1,000 mm—Multi-Folding Unit FD5030
    900 x 730 x 1,010 mm—High-Capacity Stacker SK5040
    1,200 x 700 x 1,100 mm—Plockmatic High-Capacity Stacker HCI3500
    900 x 680 x 1,060 mm—Plockmatic Multi-Purpose Stacker MPS1260
    1,420 x 700 x 970 mm—Plockmatic PBM 5035S/PBM 5035, including stacker
    Weight—mainframe 1,100 kg or less
    Weight—other 230 kg or less—Vacuum-Feed LCIT RT5150 
    40 kg or less—Bridge Unit BU5010
    20 kg or less—Multi-Bypass Tray BY5020
    9 kg or less—Vacuum-Feed Banner Sheet Tray Type S9
    23 kg or less—Extension Vacuum-Feed Banner Sheet Tray Type S14
    9.5 kg or less—Multi-Bypass Banner Sheet Tray Type S9
    250 kg—Plockmatic LCT3500 2.0
    135 kg—Finisher SR5110
    160 kg—Booklet Finisher SR5120
    75 kg—Trimmer Unit TR5050
    60 kg—Cover Interposer CI5040
    45 kg or less—Multi-Folding Unit FD5030
    131 kg or less—High-Capacity Stacker SK5040
    135 kg or less—High-Capacity Stacker SK5040 with roll-away cart
    250 kg—Plockmatic High-Capacity Stacker HCI3500
    65 kg—Plockmatic Multi-Purpose Stacker MPS1260 lift unit
    5 kg—Plockmatic Multi-Purpose Stacker MPS1260 docking unit
    Minimum space requirements 1,000 mm—front 
    1,000 mm—left 
    1,000 mm—right 
    800 mm—rear
  • Simple FAQ
    Simple FAQ Content
  • Simple FAQ - 2
    Simple FAQ Content - 2
  • Your First FAQ Question
    Your relevent FAQ answer.
Scroll to Top